Correct Shroud Replacement for an Older Coleman AC

Question

Question:

My unit dimensions are 13inch H x 32.5inch L x 22 3/4inch W. The Coleman Maxxair shroud that came up in my search looks like it should fit. Do yall recommend something else for the above dimmensions?

asked by: John

0

Expert Reply:

Correct, the Replacement RV Air Conditioner Cover for MaxxAir TuffMaxx Units # MA00-325001 you're looking at will work with your Coleman AC. This shroud measures 41-5/8" long x 29-3/8" wide x 12-3/4" tall, so it'll have plenty of room to fit your unit.

expert reply by: Bryce D

0

Coleman AC
(click to enlarge)

Answer 1

For your application we have 2 potential options: - Replacement RV Air Conditioner Cover #MA00-325001 - Replacement RV Air Conditioner Cover #MA8335A5261 The first option is designed for Mach 1, 3, and 15 AC units and measures 41-5/8" long…

view full answer...

Answer 2

From my research on the Coleman TSR Air Conditioning units, the MaxxAir TuffMax Replacement Shroud #MA00-325001 works. I've provided a diagram that shows the dimensions of the shroud and if you can verify that your unit is that size, the…

view full answer...

Answer 3

From previous customers with a Coleman TSR air conditioner that gave us dimensions we have the MaxxAir TuffMaxx Replacement Shroud #MA00-325001 that we've been able to confirm as a fit.

view full answer...

Answer 4

The best solution for your situation would be to use a circuit tester, like part #PTW2993, to wire your trailer wires to a seven-way trailer connector, like part #A7WCB. Wiring by function is the best way to make sure you have the trailer connector…

view full answer...

Answer 5

The part number of 8330-715 matches a Coleman Mach AC unit so for a shroud replacement you'd want the part #MA00-325001 that you referenced.

view full answer...

Answer 6

The the MaxxAir shroud part #MA00-325001 is a fit for the Coleman Mach, Mach 1, Mach 3 and Mach 15 models and mounts like the original and includes mounting hardware and instructions. Mach is an entire model line of Coleman air conditioners and…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Correct Shroud Replacement for an Older Coleman AC

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching