Troubleshooting Prodigy P2 Brake Controller Installed in a 2001 Chevrolet Suburban
Question:
My prodigy 2 controller stopped working on my 2001 suburban. After using it 4x the brakes will only work when manually turned on by hand on the controller. I have set up up to the highest setting and it makes no difference. All lights work and controller shows good connection.
asked by: Patrick M
Expert Reply:
Since the brakes work when you use the manual override, the first place that I would check is the fuses on your 2011 Chevy Suburban. I recommend starting with the fuse box under the hood and make sure that the fuse labeled CHMSL is good. CHMSL stands for Center High Mount Stop Light, the light at the top of the rear hatch of your Suburban. Since it is triggered with the brake lights this might be causing the issue you have with the Prodigy P2 brake controller.
The next place to check is the red wire input for the brake controller. This wire is the brake switch input from your Suburban. If you hard wire installed the brake controller, I would check the connections and make sure they are sound. To test this, you will want to use a circuit tester like the # PTW2993 and press the brake pedal while probing the vehicle side of the red wire connection, and make sure that the signal is being sent from the vehicle.
If you used a quick plug-in adapter for installation, please make sure that you are using the correct adapter. The adapter that you need is the # 3025-P, or the # 3025-S adapter. Please make sure that you are using the correct adapter with the correct pin locations specific to your 2001 Chevy Suburban.
If you have checked the options listed above and are still having these issue, please feel free to reply to me via e-mail, and I would be happy to assist you with additional troubleshooting.
I have included links to the part referenced above and a couple of helpful articles about installing brake controllers for your reference.
Products Referenced in This Question
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - GM
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Pigtail - GM
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Wired to Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Q&A: Brake Controller Recommendation for a Truck with Air Brakes and a Trailer with Electric Brakes
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Q&A: Lift Kit Options For A 2015 Winnebago Micro Minnie 1706FB
- Q&A: Should I Get a Proportional or Time-Delayed Brake Controller
- Q&A: How do I Tell if the Brake Controller is Bad
- Q&A: Recommended U-Bolts And Plate For A 1-1/2" Wide Square Axle