Will The Bearing Buddy BB2717SS Fit A Trailer That Uses 2.72" Dust Caps?

Question

Question:

Bearing Buddy 2717SS should these fit a triple axle Ameratrail Trailer that uses dust caps that are considered 2.72 OD? Thank You

asked by: Jeromey T

0

Expert Reply:

Yes, The Bearing Buddy # BB2717SS will be the correct size for hubs with the 2.72" dust caps. This is a fairly common size found on 5,200-lb to 7,000-lb rated axles.

expert reply by: Jesse M

0

Answer 1

I reached out to my contact at CE smith. I was told that the CE Smith Outrigger Poles #CE56510 weigh 5 lbs apiece.

view full answer...

Answer 2

I can tell you how to determine if the Bearing Buddy Bearing Protectors - Model 2717SS - Stainless Steel #BB2717SS are the correct fit for your hubs, but we don't have the measurements on your specific hub to know offhand. For you to confirm the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

Generally speaking bearing grease has so little water in it that significant expansion due to freezing temperatures is unlikely. Higher operating temperatures within the hubs while underway would potentially thin the grease but again not cause much…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Will The Bearing Buddy BB2717SS Fit A Trailer That Uses 2.72" Dust Caps?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching