Correct Rear Tie Down for 2020 Ram 3500 with Torklift 30k Super Magnum Hitch

Question

Question:

I need just the rear camper tie downs for a 2020 ram 3500 with a torklift 30k super magnum hitch.

asked by: Daniel L

0

Expert Reply:

The correct rear Torklift camper tie down for your 2020 Ram 3500 that has a Torklift Super Magnum Hitch is the part # TLR3510.

expert reply by: Jameson C

0

Answer 1

When it comes to higher towing capacities and hitch extensions the Torklift extensions are the only way to go like with the part #TLE1536. So to use this with your 2021 Ram 3500 you would need the Torklift hitch part #TLD1111-30 which fits…

view full answer...

Answer 2

Yes. In order to bumper tow a trailer of that size and use a TorkLift Everest system like the #TLWD1000 you'll need to remove the factory hitch and install a dual receiver like the TorkLift SuperHitch Magnum Trailer Hitch Receiver - Custom…

view full answer...

Answer 3

Yes we have the solution for you. TorkLift SuperHitch Magnum Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2" and 2" part #TLD1111-30 is a confirmed fit for your 2019 Ram 3500 dual rear wheel as long as it has the factory…

view full answer...

Answer 4

Thanks for the picture! To use the TorkLift SuperTruss Hitch Extension 48" Long item #TLE1548 with your 2022 Ram 3500 you are going to want the TorkLift SuperHitch Magnum Trailer Hitch Receiver item #TLD1111-30. This hitch is custom fit and…

view full answer...

Answer 5

The proper extension for your setup would be the one that allows you to have clearance of your hitch mounted accessory and also allows you to still be able to pull the steps down. If the receiver tube sticks out past the camper too far then you will…

view full answer...

Answer 6

Yes, in order to install the TorkLift SuperHitch Magnum Trailer Hitch Receiver #TLD1111-30 on your 2019 Ram 3500 you will need to first remove the factory trailer hitch. On the new Ram trucks this does require a bit of an effort but unlike previous…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Correct Rear Tie Down for 2020 Ram 3500 with Torklift 30k Super Magnum Hitch

Product Page this Question was Asked From

Continue Researching