Replacement Grommet for LED Trailer Mini Clearance and Side Marker Light

Question

Question:

I am looking for replacement grommets for the 3/4 inch bullet lights. They are for a cargo trailer with 18 guage thick walls. The grommets I have now are made for the 18 guage thickness only. Not the common 1/16 to a quarter universal ones I see everywhere else. Do you guys carry those. Im having no luck finding these

asked by: Steve

0

Expert Reply:

The replacement grommet for the LED Trailer Mini Clearance and Side Marker Light with Grommet # MCL10AKB is found as part # A11GB and will fit just fine with 18 gauge and 1-1/16" thick walls

expert reply by: Jon G

0

Answer 1

The grommet measures about 1/8" thick and the inner diameter is 1/4". The inner diameter of the front of the grommet where the light goes is 1". I have attached a diagram for your reference.

view full answer...

Answer 2

Hi Dave, I have an option for for you, however, I wasn't able to cross reference the number you gave me so you'll just need to take a couple quick measurements to confirm the following option will work as a direct replacement. If the…

view full answer...

Answer 3

The ideal thing to do when adding wiring to any vehicle would be to use existing holes already made in the firewall. If you do not have any existing holes then you will want to drill in a place that is close to where you are needing to run the wire.…

view full answer...

Answer 4

The Optronics LED Trailer License Plate Light #LPL12CB, along with the Ear Mount Bracket #A11GLPB referenced in your question, should work very nicely with the 1-1/4 inch hole you mentioned having on your trailer. The ear mount bracket has a total…

view full answer...

Answer 5

Yes, because it is a 3-wire light, you can wire the Red Identification Light Bar with White LED Utility Light #OPT88FR to function as rear marker and reverse lights.

view full answer...

Answer 6

For the Tecnic 45 degree accent light part #TN42FR the correct mounting cover is the part #TN34FR.

view full answer...

Answer 7

Since your old V-bar light only uses a single wire it grounds the light through the mounting hardware. You will simply need to add a Ring Terminal #DW05736-1 to the ground wire on the V-Shaped Identification Light Bar #TN23MR. Then you will be able…

view full answer...

Answer 8

Manufacturers do not list the part numbers they use to the public so I would need to see the actual part numbers listed on the slide out motor to determine the correct replacement. I've attached a picture below of where the stickers are typically…

view full answer...

Answer 9

The Mounting Flange for Optronics Uni-Lite Trailer Lights #A11PB can replace a rubber grommet but is made of ABS plastic so it wouldn't form a watertight seal. If your trailer needs a watertight seal then you'll need the rubber grommet for a…

view full answer...

Answer 10

The LED Trailer Mini Clearance and Side Marker Light with Grommet #MCL10AKB will fit best with a wall (or bracket) thickness that is just under 5/16".

view full answer...

Answer 11

The correct replacement gear pack for your Lippert slide out will depend on the size of the arms attached to your slide out: - 2" x 3" Slide Arms: Lippert Standard Slide-Out Gear Pack #LC140409 - 2-1/2" x 2-1/2" Slide Arms:…

view full answer...

Answer 12

You'll need to measure the arm (pictured below) to determine the correct size gear pack replacement for your trailer's slide outs. For 2" x 2" you'll need #LC281331 For 2.5" x 2.5" you'll need #LC123356 For 2"…

view full answer...

Replacement Grommet for LED Trailer Mini Clearance and Side Marker Light

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching