Do K-Source Snap & Zap Towing Mirrors Fit 2018 Ram 2500 With Chrome

Question

Question:

I have a 2018 ram 2500 laramie with chrome mirrors Will these mirrors work on my truck

asked by: John H

0

Expert Reply:

Yes, your 2018 Ram 2500 with chrome mirrors will be able to use the Snap & Zap, with the correct part number being the following:

- K-Source Snap & Zap Custom Towing Mirrors # KS80710

expert reply by: Kyle S

0

Answer 1

Yes, the K-Source Snap & Zap Custom Towing Mirrors #KS80710 referenced in your question will fit the chrome mirrors on your 2016 Laramie Ram 1500.

view full answer...

Answer 2

For your 2018 Ram 2500 with chrome mirrors, turn indicators built into them, and puddle lights the K-Source tow mirrors part #KS80710 are a confirmed fit. The mirrors have cut outs in the bottom of them to allow the puddle lights to work and…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 8

Hey Jeff, The Pace Edwards JackRabbit Retractable Hard Tonneau Cover w Explorer Rails #311-JED7833 is designed for a 6-1/2' bed while the #311-KRD7936 is designed for an 8' bed. Since you have a 6-1/2' bed the #311-JED7833 would be the…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The Replacement Hardware Kit #AABRKT-5056 will fit the Aries Pro Series Grille Guard #AAP5056. This is the upgraded version of the Grille Guard #AA5056 which uses the same install hardware to attach to a truck.

view full answer...

Answer 11

Installing ta Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Adapter Pin Box like the #325-GH-8045 would not void the warranty of your camper, and Gen-Y makes some of the most durable parts on the market. I really like this as an alternative to…

view full answer...

Answer 12

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...