Size of Lionshead Trailer Wheel Swivel Flange Lug Nut

Question

Question:

I see where the stud that it fits is a 5/8” but I can’t seem to find anywhere that states the nut/socket size. So what is the Nut size?

asked by: Monte L

0

Expert Reply:

In this case, the size of the wheel stud it fits and the size of the nut are interchangeable for size; the Lionshead Trailer Wheel Swivel Flange Lug Nut # LI84FR is a 5/8"-18 nut.

expert reply by: Kyle S

0

Answer 1

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 2

Dexter Flange Wheel Nut #95188 is sold individually so you will need to order the specific quantity you want when placing your order. The nut has an inside diameter of 5/8-inches,18 threads per inch and it is shown in the linked photo.

view full answer...

Answer 3

For the Dexter 10K axles a 5/8" wheel nut #95188.

view full answer...

Answer 4

You can't use conical/tapered lug nuts like the #12CLN on wheels with flat bolt seats; instead you'll want to use a lug nut with a flange like the Flange Wheel Nut - 5/8" #95188. If you can tell me which wheels you've got and the lug…

view full answer...

Answer 5

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life so there is typically no…

view full answer...

Answer 6

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 referenced in your question do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Size of Lionshead Trailer Wheel Swivel Flange Lug Nut

Product Page this Question was Asked From

Continue Researching