Lock Cores For Replacement Cable Lock Assembly for Yakima HoldUp Bike Carriers

Question

Question:

I need to change the key system of Item # Y8890284, can you tell me what key system I should buy and what master key number I buy to remove the old ones

asked by: Victor

0

Expert Reply:

For lock cores to use with the Replacement Cable Lock Assembly for Yakima HoldUp Bike Carriers # Y8890284 you just need the following:

- Yakima Same Key System (SKS) Lock Cores (QTY 2) # Y07202

This comes with lock cores (they aren't sold in singles unless you want a specific lock number), as well as the master key so you don't have to have that separate.

expert reply by: Kyle S

0

Answer 1

I checked with Curt and the etrailer Trailer Hitch Receiver part #e38KR is a fit for a 2023 Kia Sportage AWD Hybrid. There are no further modifications needed for this sub-model, it features a bolt-on no drill or cutting installation. Please note, if…

view full answer...

Answer 2

The B&W Companion OEM 5th Wheel Hitch for Ram Towing Prep Package #BWRVK3600 weighs 212 lbs.

view full answer...

Answer 3

If your OEM hitch is simply bolted into place onto the crossmember, you could indeed remove it and install the Draw-Tite 76310 which we sell as #DR64FR Class III hitch in its place. If the existing hitch is welded into place, it could be an integral…

view full answer...

Answer 4

There are a couple of pretty big differences between the Draw-Tite Trailer Hitch Receiver #DR64FR and the Curt Trailer Hitch Receiver #CU74FR that fit your 2020 Jeep Gladiator, and I'll go over them so you can decide which trailer hitch is the…

view full answer...

Answer 5

So that they don't have to translate their instructions into several languages Yakima makes all of their install instructions diagrams as the visual is a "universal" language. Let's see if I can help though. I attached the picture…

view full answer...

Answer 6

In order to replace the bike lock cable on the Yakima HoldUp Bike Rack like part #Y02443 you will need to use the Replacement Cable Lock Assembly part #Y8890284. There would be no way to unlock the core you have now if the face was damaged but this…

view full answer...

Answer 7

Yes, you can plug a trailer side 4-way trailer connector part #002402 into a vehicle side 5-way connector part #HM37908 without any adapters needed.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...