Self-Adjusting Brake Assemblies For Lippert 4,400LB Axle On 2023 Grand Design Imagine AIM 15RB

Question

Question:

2023 imagine aim 15rb looking to replace brakes with auto adjusting ones. Cant seem to locate on your site. Are they available?

asked by: Charles S

0

Expert Reply:

You will need the Left # LC96WD and Right # LC46WD Lippert Electric Trailer Brake Assemblies for your 2023 Grand Design Imagine Aim 15RB. These are self-adjusting brake assemblies to replace the brakes on your Lippert 4,400lb axle.

expert reply by: Bud M

0

Answer 1

Hey Mario, the correct brake assembly set you need for the 4,400 lb axles on your trailer is the part #LC46WD and #LC96WD. Then for a hub/drum you'd want the part #8-407-5UC3-EZ and you'd be set. The hub includes all the needed bearings and…

view full answer...

Answer 2

We do carry the Lippert Electric Trailer Brake Assemblies Left #LC96WD and Right #LC46WD from Lippert for their 4,400lb axles. These brakes are self-adjusting like the Electric Trailer Brake Kit #AKEBRK-35-SA.

view full answer...

Answer 3

It certainly does. What you have there is a hub for a 4,400 lb axle. To replace it you will need the #8-407-5UC3-EZ. This includes the hub/drum, new bearings, races, grease seal and lug nuts.

view full answer...

Answer 4

The Trailer Hub and Drum Assembly part #8-407-5UC3-EZ is sold individually or as a quantity of one. It will require two per axle for a complete set.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Self-Adjusting Brake Assemblies For Lippert 4,400LB Axle On 2023 Grand Design Imagine AIM 15RB

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching