Can the Camco Replacement 90 Degree Exhaust Pipe Be Used to Replace the Pipe on a Generac 4709

Question

Question:

Can your Gen-Turi exhaust pipe be used to replace the exhaust pipe on a Generac model 4709 Quietpac 40G?

asked by: William S

0

Expert Reply:

Possibly, but you'd have to measure your current exhaust pipe first. The Replacement 90-Degree Exhaust Pipe for Camco Gen-Turi RV Generator Exhaust System # CAM44812 has the same diameter aside from the shorter end where it gets larger to accept a 1-1/2" diameter pipe which I've shown in the attached diagram.

So if your Generac model 4709 Quietpac 40G uses up to 1 1/2" piping you'll be good to use this as a replacement.

expert reply by: Bryce D

0

Pipe Diameter
(click to enlarge)

Answer 1

For your generator exhaust, the Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe #CAM44812 is designed to be used with the Camco Gen-Turi RV Generator Exhaust System #CAM44461. With that being said, we have not tested the…

view full answer...

Answer 2

The inner diameter of the expanded ends of the part #CAM44812 is 1.53 inches and the outer diameter of the non expanded end is 1.51 inches. So basically this setup is designed to either slip into a 1-1/2 inch pipe or slip over a 1-1/2 inch pipe.

view full answer...

Answer 3

I went out to our warehouse and doublechecked the length myself and found the overall length of the Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe #CAM44812 to be 30" when including the bend. You are correct that the…

view full answer...

Answer 4

The easiest way to install the TST TPMS for RVs #TST-507-FT-6-C on hard to reach dually valve stems would be to first install some valve extenders like the Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" Dually - Hub Mount -…

view full answer...

Answer 5

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

Hi James, To my knowledge the Reese Goosebox is the only replacement option that won't void the frame warranty. That being said, the frame warranty is typically only a year so you really aren't losing much voiding it, especially if you've…

view full answer...

Answer 9

Hi Joe, I assume you are referencing an Equal-i-zer weight distribution since you have shank #EQ90-02-4700. I went ahead and read the owners manual for their systems and there is noting regarding adjusting the angle of the hitch ball. The hitch head…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Can the Camco Replacement 90 Degree Exhaust Pipe Be Used to Replace the Pipe on a Generac 4709

Product Page this Question was Asked From

Continue Researching