How Much Ground Clearance is Lost with Curt Rebellion XD Adjustable Ball Mount 8 inch Drop

Question

Question:

How far down from the hitch tube does the C57UR hitch hang? As far as ground clearance?

asked by: Tyler

0

Expert Reply:

The Curt Rebellion XD part # C57UR measures 10 inches from the bottom of the shank that inserts into the hitch opening to the bottom of the ball mount. So you would lose 10 inches of ground clearance measured from bottom of your hitch.

expert reply by: Jameson C

0

Answer 1

The Curt Rebellion XD Shock Absorbing Adjustable Ball Mount w/ 2" and 2-5/16" Balls #C83WR is 8" from the bottom of the receiver shank to the bottom of the adjustable mount.

view full answer...

Answer 2

The Curt Rebellion XD Shock Absorbing Ball Mount #C83WR is compatible with Rock Tamers, but the only way to make sure you will have enough clearance is to measure from the center of the hitch pin hole to the front edge of your trailer hitch receiver.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

Hi Tyler, When adding in air springs on a lifted vehicle the proper way to determine the correct sized spacer is to first install the upper and lower brackets and then measure the distance between them and subtract the height of the air spring bellow…

view full answer...

Answer 9

The answer to your question will depend on how you use your truck. Vehicle-based systems like the RoadActive Suspension system or air bags will work just fine with a weight distribution system, but they work best to suspend weight being hauled in the…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

How Much Ground Clearance is Lost with Curt Rebellion XD Adjustable Ball Mount 8 inch Drop

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching