Amperage and Voltage Rating for Sealed, Uni-Lite Mini LED Side Marker and Clearance Light MCL11AKB

Question

Question:

What is the voltage range these lights are designed for? Cant find any specs...

asked by: Broderick C

0

Expert Reply:

Sealed, Uni-Lite Mini LED Side Marker and Clearance Light # MCL11AKB is rated at 0.047 amps at 12 volts. It is designed for a 12 volt system. A 12 volt system can actually fluctuate slightly higher and lower than 12 volts.

The LEDs will work on a lower voltage 6-volt system but they will not be as bright. A 24 volt system is not recommended for these lights.

expert reply by: Michael H

0

Randy K.

2/18/2020

Thanks for the reply.. I’m going to order a couple led lights from you. Thanks for your time ..

Reply

Randy K.

2/15/2020

I need a portable led marker light For my trailer. Going to use a RC 7.2 volt battery to run a 3/4 “ led light.. Do you think this application would work?

Reply

Jason S.

2/17/2020

Although not designed for this use, I believe it will work. You will need to do some calculations or testing to ensure you have the number of hours the battery will last for that application. The LED lights like # MCL11AKB require only 0.03 amps at 12.8v. The similar red marker light # MCL121RK9PVG requires 0.04 amps at 12.8v. I believe the RC batteries are designed for high amperage output, so I believe it would work, but can't confirm as we haven't tested it and it isn't designed for that application.

Reply

Answer 1

The first thing I recommend doing is to check that the ground wire for the lights is securely attached to a clean metal surface on the trailer frame. A loose ground wire will keep the lights from working. If the ground attached to the trailer does…

view full answer...

Answer 2

You may not even need load resistors to switch to LED lights. The best thing to do is to try the lights without load resistors first. No need to purchase something you may not need until you know need it. Load resistors such as #DI34ZR dissipate heat…

view full answer...

Answer 3

The Optronics #MCL13A2B Sealed Mini LED Side Marker lamp draws 0.046 amps at 12.8 volts. I'd recommend using 16-18 gauge wire for your trailer lighting circuits. If you're rewiring your trailer, we carry a bonded 3-wire, part #16-3B-1 which…

view full answer...

Answer 4

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 5

The only way to have clearance lights on your trailer that also flash with the turn signals is to have multi-function light assemblies that feature a separate wire for each the running lights and turn signal circuits. If your existing clearance…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

When installing an awning like the Solera Smart Arm 12V Power RV Awning #LC517486, the arms will be secured to the wall framing. When the awning extends there will be quite a bit of leverage, so it is important to mount the awning to an area where…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 12

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Amperage and Voltage Rating for Sealed, Uni-Lite Mini LED Side Marker and Clearance Light MCL11AKB

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching