Overall Length of Trailer Idler Hub Assembly for 2,000 lb Axles

Question

Question:

what is the oal of hub assembly AKIHUB-440-2-G-1K

asked by: Greg P

1

Helpful Expert Reply:

By "oal" I believe you are asking about the overall length; I measured the Trailer Idler Hub Assembly # AKIHUB-440-2-G-1K and found it was 4-1/4" long.

expert reply by: Kyle S

1

Answer 1

The Dexter Trailer Idler Hub Assembly #8-91-05UC1 comes with the Bearings #L44649. You do have the option to order 2 of the Trailer Hub Bearing #L44643 and simply use these when you install the hub as they both use the same size Race #L44610. I would…

view full answer...

Answer 2

Hey Bruce, thanks for writing in, and unfortunately you have what is called a stub spindle, and it's 3 inch length won't allow you to use the Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized #AKIHUB-440-2-G-1K. There…

view full answer...

Answer 3

We normally recommend short beds to use a slider like you mention for clearance issues. The B&W Companion Slider for the 2020 Chevrolet Silverado 3500 with OEM prep package is not available yet. It is expected to be available September of 2019.…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 6

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Overall Length of Trailer Idler Hub Assembly for 2,000 lb Axles

Product Page this Question was Asked From

Continue Researching