Replacement Options For An Atwood 33636E Propane Gas Detector

Question

Question:

Do they still make RV Propane Gas Detector #33636E ? If not what replaces it?

asked by: Jerry

0

Expert Reply:

Atwood propane detectors have been on and off available since the Atwood brand was bought out and slowly killed off by Dometic so you'd be hard pressed to find one at this point. We currently only offer the RV Safe brand which has either just propane gas detection or models with propane gas and carbon monoxide detection. Each of these come with trim plates that are a surface mount design to cover up any gaps left behind by the old unit. The small trim measures 5-3/4" long x 4-1/4" wide and the large trim measures 7-1/4" long x 3-3/8" wide. I've listed the available options below for you:

Propane Gas Detection:
White # RS64FR
Black # RS44FR

Propane Gas And Carbon Monoxide Detection:
White # RS34FR
Black # RS54FR

expert reply by: Kevin C

0

Answer 1

Atwood is no longer in business so you'd have to switch over to a new brand in order to get what you need. We currently only carry the RV Propane Gas #RS44FR (white #RS64FR) which comes with two different trims (large: 7-1/4" long x…

view full answer...

Answer 2

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 3

RV propane detectors will typically only have an internal battery and will not have one that you can replace. Two-wire systems like the RV Propane Gas Detector #RS44FR would wire directly to the trailer battery for power.

view full answer...

Answer 4

The Atwood RV Carbon Monoxide and Propane Gas Detector - 12 Volt - White #AT36681 utilizes a wall cutout size of 3-9/16" long x 3-7/16" wide x 1" deep. This is the replacement for the GS961LP you referenced. I've linked a diagram…

view full answer...

Answer 5

We have exactly what you are looking for. You will want the Atwood combination gas and carbon monoxide detector #AT36681.

view full answer...

Answer 6

The RV Propane Gas Detector part #RS64FR for white or part #RS44FR for black is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you…

view full answer...

Answer 7

We do have some LP gas detectors available, but none would be a direct replacement for your CCI 7770.2 / Pre Tell 22. From what I could find on your CCI 7770.2 / Pre Tell 22, it has dimensions of 6.25" wide x 3.9" tall. The RV Propane Gas…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

I recommend the #RS34FR to replace your current LP gas detector. This is a simple 2 wire design making for easy installation.

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The RV Propane Gas Detector part #RS64FR is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you had for the previous so it will be a…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...