Replacement Bail Clamp for Firestone Air Bag Kit # F2597

Question

Question:

I need a replacement bail clamp for Firestone airbag kit 2597. Can you point me in correct direction Thx

asked by: Matthew T

0

Expert Reply:

The correct replacement bail clamp for a Firestone air bag kit part # F2597 is the part # F3077.

expert reply by: Jameson C

0

Answer 1

I went out to our warehouse to take a look at all of the Replacement Bail Clamps we currently have available for the Firestone Ride-Rite Air Helper Springs. For both the Replacement Bail Clamp #F3373 and #F3077, there is a distance between threaded…

view full answer...

Answer 2

The correct replacement bail clamps for the Firestone Ride-Rite Air Helper Springs part #F2582 are the Replacement Bail Clamp for Firestone Ride-Rite Helper Springs part #F2135823410.

view full answer...

Answer 3

For the U-bolt part #F3373 the dimensions are: The outer width is 6-3/4" and the inner width is 6" The outer length is 4-3/4" and the inner length is 4-3/8" The length of the threaded portion is about 2 inches

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Replacement Bail Clamp for Firestone Air Bag Kit # F2597

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching