Kit for Allowing Flat Towed Vehicle to be Flat Towed

Question

Question:

I need to charge my Jeep battery on long trips. Do you have a trickle charging system to run from my RV ?

asked by: Bob J

0

Expert Reply:

We do have charge line kits that are what you are looking for. If the 7-way at the rear of your motorhome does not have a 12 volt accessory circuit you'd need the part # RM-156-75 which will complete this and/or for the side on the flat towed vehicle you'd want the part # RM-156-25.

expert reply by: Jameson C

0

Answer 1

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 12

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Kit for Allowing Flat Towed Vehicle to be Flat Towed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching