How to Install Malone FoldAway-5 on a TracRac SR Ladder Rack

Question

Question:

Would this work on my TracRack SR and the Malone Foldaway-5?

asked by: Trevor

0

Expert Reply:

The Aero Style Crossbar T-Slot Fit Kit # MAL37AR will work with your TracRac SR ladder rack MPG4125 but it doesn't come with the correct hardware for the Malone FoldAway-5 # MAL38FR. Instead, you'll need the kit # MAL27AR which uses the same plate, but it comes with two of them and the correct hardware to get your kayak carrier properly mounted to your ladder rack.

expert reply by: Jon G

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 3

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

Hi Alec, The Inno Kayak Roof Rack w/ Tie-Downs #INA452 needs a 28" minimum spread so that the saddles sit at the right spot for the kayak and support the weight properly. This is probably just a general guide from Inno though because the length…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

How to Install Malone FoldAway-5 on a TracRac SR Ladder Rack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching