Wiring The Brakeaway Switch On The Bright Way Brakeaway Kit BW94FR
Question:
I have a wiring question. I purchased the BW94FR breakaway switch and the #3375601101 junction box. I can understand most of the wiring - except the back wire coming out of the switch...which I think is for the flashing lights....? My trailer wiring has green, brown, and yellow in addition to black, white and blue - which I figured was truck power, ground, and brake which I believe is lights/turn signal/stop? how would I wire this on the JB terminals - jumpers perhaps? Thanks, Joe Picoraro
asked by: Joe P
Expert Reply:
The Black wire coming from the breakaway switch would run to your junction box and connect to your brake wire terminal (this should be blue or black). The blue wire coming from the switch would go to the blue wire on the battery box. As far as connecting the wire you can use crimp connectors or better yet heat shrink connectors like #DW05745-5. We can provide these of course, or you should be able to find them at any hardware or electrical supply store.
I have included a picture of a diagram, as well as a link to an install video below.
Products Referenced in This Question
Trailer Wiring Junction Box - 7 Color Coded Terminals - ABS
- Accessories and Parts
- Trailer Wiring
- Junction Box
- Buyers Products
more information >
Ring Terminal - 12-10 Gauge Wire - 3/16" Ring ID
- Wiring
- Wire Connectors
- Ring Terminals
- 3/16 Inch Diameter
- 12-10 Gauge
- Flint Hill Goods
more information >
Bright Way Push-to-Test ICU Trailer Breakaway Kit with 0.5-Amp Charger and 5 Ah Battery - Side Load
- Trailer Breakaway Kit
- Kit with Charger
- Single-axle
- Tandem-axle
- LED Tester
- .5 Amp Charger
- Battery Included
- 5 Ah
- Bright Way
more information >
Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5
- Wiring
- Wire Connectors
- Butt Connectors
- 12-10 Gauge
- Deka
more information >
Product Page this Question was Asked From
Bright Way Push-to-Test ICU Trailer Breakaway Kit with 0.5-Amp Charger and 5 Ah Battery - Side Load
- Trailer Breakaway Kit
- Kit with Charger
- Single-axle
- Tandem-axle
- LED Tester
- .5 Amp Charger
- Battery Included
- 5 Ah
- Bright Way
more information >
Continue Researching
- Video: Review of TruRyde 1 Inch Diameter Trailer Spindle Castle Nut - 165686
- Video: Bulldog Winch Cinch Straps Review
- Video: Review of MaxxTow Trailer Winch - Standard Hand Winch - MT50156
- Video: etrailer Trailer Idler Hub Assembly Installation
- Video: Bulldog Winch Tie Down Straps - Truck Bed - BDW20338 Review
- Video: Review of Fulton Trailer Winch - Standard Hand Winch - F99CR
- Shop: Trailer Spindle Nut 1"
- Shop: Bright Way Push-to-Test ICU Trailer Breakaway Kit with 0.5-Amp Charger and 5 Ah Battery - Side Load
- Shop: Fulton XLT Single Speed Winch - 8" Long Handle, 20' Strap and Cover - 1,500 lbs
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Search Results: 165686
- Shop: CE Smith Spool Roller Assembly for Boat Trailers - Galvanized Steel and Black Rubber - 4"
- Search Results: break away switch wiring
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles
- Shop: Trailer Wiring Junction Box - 7 Color Coded Terminals - ABS
- Search Results: breakaway battery box
- Search Results: break away
- Article: Trailer Wiring Diagrams
- Q&A: Replacement # 84 Spindle Recommendation to Replace a Trailer Spindle
- Q&A: Installing TRU77FR Spindle
- Q&A: Wiring Connections For Bright Way Push-to-Test ICU Trailer Breakaway Kit # BW94FR
- Q&A: Should Blue Wire on Trailer Have Power
- Q&A: Spindle Replacement for 3500 lbs Axle
- Q&A: How To Run Grounds for Lights on an Aluminum Frame Trailer
- Q&A: How to Wire a Trailer with Electric Brakes
- Video: Optronics RV Lighting - Ceiling Light - ILL29CB Review
- Search Results: ill78cbb
- Shop: Vehicle Lights