Recommended Crossbars For a 2014 Honda CR-V to Use the Thule Hullavator Pro

Question

Question:

What is this THKIT3118 Kit that is mentioned in what I need to mount roof racks for Hullavator?

asked by: Donna

0

Expert Reply:

The fit kit THKIT3118 you're looking at is a discontinued part but don't worry we got you covered. To mount the Hullavator Pro # TH898 to your 2014 CR-V, I recommend going with the aero Thule WingBar Evo Crossbars # TH711420, with the clamp feet # TH710501, and the fit kit # TH145108 instead.

These bars measure 53" long x 3-1/8" wide x 1" tall, and has a dynamic (vehicle in motion) weight capacity of 220 lbs.

These crossbars will serve as the perfect mounting point for the Hullavator # TH898 and any other future roof accessories you might use.

expert reply by: Bryce D

0

Answer 1

Yes we have exactly what you are looking for! I'll give you a couple of options and explain the difference for you. To start I really like the Rhino Rack setups that we have. They offer high quality components and a lot of bang for the buck. The…

view full answer...

Answer 2

If there was a way to lighten your kayak by 5 lbs the Thule Hullavator part #TH898 that you referenced would work great but it has a 75 lb weight capacity. This does fit the Rhino Rack Vortex Aero roof racks though like the part #RRVA137B-2,…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 7

The Thule Hullavator Pro, part #TH898, does in fact need crossbars that extend 4" - 8" beyond the feet. To use the flush rails on your 2021 Toyota RAV4, you will need a roof rack that has feet that are compatible with the rails. With those…

view full answer...

Answer 8

There is not a general restriction from Thule that says two Hullavator Kayak Carriers #TH898 can't be used on a Thule roof rack. As long as the crossbars on your Ford Escape have the required length for two sets and a sufficient weight capacity…

view full answer...

Answer 9

For your 2018 Honda HR-V to be compatible with the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs #TH898, you have to use slightly longer crossbars. The Hullavator requires 4-8 inches overhang to give clearance. In order to give…

view full answer...

Answer 10

Yes, you will be able to use the Thule Hullavator Pro Kayak Roof Rack #TH898 with the Rhino-Rack Vortex Aero roof rack having 59" crossbars. You will need the Crossbars #RRVA150B-2, Legs #RRRLKVA and Fit Kit #DK079 to complete the rack on your…

view full answer...

Answer 11

There are two ways to connect the Thule Hullavator to your crossbars, clamp on or use the T-slot. Clamp on requires square bars and T-Track requires a Thule Crossbar. If you have raised side rails on your vehicle, the SteelTop #MPG203 will just clamp…

view full answer...

Answer 12

Hello Paul thanks for your question. When installing the Thule Hullavator Pro #TH898 it is completely normal to have 4 leftover bolts. The length of the bolt you use is determined by what kind of crossbar you are using. The 35mm bolts are intended…

view full answer...