7-Way RV-Style Trailer Connector For 2014 Chevrolet Silverado

Question

Question:

polllak 11996 2014 chevy silverado W/T 8 ft bed. It is listed thru 2013 , 2014 has twist in factory. will Pk 11996 fit.

asked by: Jim

0

Expert Reply:

If you have damaged the connector on your 2014 Chevrolet Silverado 1500, the replacement you will want is the Pollak Twist-in, 7-Pole, RV-Style Trailer Connector, part # PK11916. I have attached links to a product review for this connector and also an installation of this connector on a 2013 silverado.

If you need to replace the wiring that attaches to the back of the harness on the rear of your truck, the Pigtail Wiring Harness, part # PK11998, is what you will need. It will hardwire to your truck wiring and attach to the back of the connector on the back of your truck. This would attach to the # PK11916. I have attached an installation video for this wiring harness.

I also recommend the Dielectric Grease for Electrical Connectors, part # 11755, whenever you are connecting electrical components. This combats corrosion and is water resistant.

expert reply by: Jeffrey L

0

Answer 1

I have attached a photo for you below which shows how both a vehicle side and trailer side trailer connector is typically wired. I say typically because this is not always exact and so long as the trailer and vehicle side both match it will not…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

7-Way RV-Style Trailer Connector For 2014 Chevrolet Silverado

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching