Does MORryde Hitch Mounted Stabilizer # MR22AR Have Minimum Hitch Tongue Weight Requirement

Question

Question:

Is there a minimum weight that your receiver hitch needs to meet? I think the hitch on the back of my Cougar 5th wheel is only rated to 300lbs?

asked by: Ken C

0

Expert Reply:

The MORryde hitch stabilizer part # MR22AR does not have any tongue weight minimum requirements for the hitch it is used in. It doesn't put that much stress on a hitch when used properly so it was not rated at all. Your hitch that has a 300 lb rating would be totally safe.

expert reply by: Jameson C

0

Answer 1

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 2

Good question, and we have asked the manufacturer, Ark, this very same question, and they have said there is not any weight rating for the Ark Drop Down Corner RV Stabilizer Jacks - 33" Long Corner Steadies #ARK77FR. They say the reason they…

view full answer...

Answer 3

The Ark Drop Down Corner RV Stabilizer Jacks - 2-1/2' Long Corner Steadies - Qty 2 #AR94FR you were looking at would do a great job of keeping your 2021 Rockwood Roo 21SSl steady, and offer a much larger foot than a standard scissor jack so they…

view full answer...

Answer 4

I have attached a few photos for you with all the dimensions we have for the Ark Drop Down Corner RV Stabilizer Jacks part #AR34FR. That said, Ark is an Australian company so the measurements are in metric, millimeter to be specific so you may need…

view full answer...

Answer 5

The weld-on mounting bracket for the ARK #AR94FR Drop Down Corner RV Stabilizer Jacks measures 4-5/8 x 2-7/8 inches. The bracket has holes for the hardware that attaches the jack to the brackets. The holes are 2-7/8 inches apart on center. I've…

view full answer...

Answer 6

The correct MORryde Quick Connect RV Steps for a 35" threshold height is part #MR32JR.

view full answer...

Answer 7

It sounds like you might be trying to pick out a set of stabilizer jacks for your trailer. If that is the case then what you will want to do is park your trailer on flat-level ground and then level it. Once this is done you can then measure from the…

view full answer...

Answer 8

The stabilizer jack I recommend for your enclosed cargo trailer is the Drop Leg Stabilizer Jack #TJ01RT because it will work well to stabilize your trailer for loading and unloading and is easy to engage when needed. The #TJ01RT drop leg stabilizer…

view full answer...

Answer 9

The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger part #PD4060K has a built-in converter which will charge the batteries using shore power. It does not contain an inverter or transfer switch which will power the appliances…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Really you're going to need to measure the distance where the leveling system is going to be installed. If that distance is more than 20', then you're going to want the 6 point Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling…

view full answer...

Answer 12

Both of the ARK stabilizer jacks #ARK94FR and #ARK87FR can rotate 90 degrees forward and back so in a way it is 180 degrees like you asked about. The difference is the #ARK94FR has a square tube and #ARK87FR has a round tube. These are both going be…

view full answer...

Does MORryde Hitch Mounted Stabilizer # MR22AR Have Minimum Hitch Tongue Weight Requirement

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching