Air Fitting for Top of Air Bag of Firestone Ride Rite Kit F2410

Question

Question:

Is this the replacement air fitting for the ride rite kit made for the 2005-2023 Tacoma. My kit came with a fitting too large. I believe it’s kit F2410

asked by: Kahen R

0

Expert Reply:

For the Firestone Ride Rite kit part # F2410 the correct elbow connector fitting is the part # F3031-1 which I confirmed with Firestone.

expert reply by: Jameson C

0

Answer 1

The Firestone Air Ride system that fits your 2013 Ford Van and uses the 6781 air bag is the Firestone Ride-Rite Air Helper Springs #F2153. The correct replacement parts are listed below: - Replacement Air Spring for Firestone Ride-Rite Kit #F6781…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will but you may need a spacer. The reason I say may is most 3" lifts are not 3" in the rear. If your 2013 Toyota Tacoma has less than a 2" lift in the back then all you will need is the Air Lift LoadLifter 5000 Air Helper…

view full answer...

Answer 12

I checked with Curt and the Front Hitch for your 2018 Toyota Tacoma TRD #C31075 is a confirmed fit and there are no notes in the install instructions that indicate that the skid plate would need to be removed or modified. The air dam needs to be…

view full answer...

Air Fitting for Top of Air Bag of Firestone Ride Rite Kit F2410

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching