Recommended Jack Pads for Leveling Systems w/ 10 Inch Round Concave Jack Feet

Question

Question:

Hello, Will the Stromberg Carlson Item # SC29MR jack pads work on my 9000 lb. Powergear 10inch dia. round concave foot not flat hydraulic jacks? Thanks

asked by: Mike

0

Expert Reply:

I have a solution for you but the Stromberg Carlson RV Jack Pads item # SC29MR do not work with concave feet. Instead you will want the SnapPad Prime Jack Pads for Power Gear Leveling Systems w/ 10" Round Concave Jack Feet item # SP84FR4. These are specifically designed for 10" round concave jack feet.

expert reply by: Jerred H

0

Answer 1

The SnapPad Prime Jack Pads #SP84FR4 are specifically designed to fit the Power Gear Leveling Systems w/ 10" Round Concave Jack Feet on your 2014 Fleetwood Bounder 34B. The Pads #SC99MR Stromberg told you to use will not fit on your Bounder…

view full answer...

Answer 2

That's a good question and the difference between the two SnapPad Jack Stand Pads for Motorhome are different shapes and depths, it isn't solely the notch in the center. I added photos of the two pads side-by-side so you can see the…

view full answer...

Answer 3

For a 9 inch diameter jack foot pad I would go with the SnapPad part #SP54FR4 over the Stromberg part #SC99MR since the SnapPad will be a little bit larger in diameter which distributes the weight a little better.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 12

Hey Brad, thanks a bunch for going ahead and getting all those measurements in advance. Based on the measurements you've given, the TorkLift GlowStep Revolution Uprising Steps w/ Booster Step #TL52SR will work perfect for your coach. These steps…

view full answer...

Recommended Jack Pads for Leveling Systems w/ 10 Inch Round Concave Jack Feet

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching