Replacement Arm Assembly for 63 inch Flat Solera Awning

Question

Question:

I have a 2022 alliance valor 40v13. With solera power awning. I need the front arm assembly for the front canopy. Heres reference # off tag: 12299 Pl-12565. 9999ROP-0006650246 Hardware REGALBL-63-FLATBK-BRMWRE V090431840 mfg date 7-15-21. With this information could u help me get right part number I need.

asked by: Kim S

0

Expert Reply:

For your flat 63 inch Solera awning the correct replacement arm assembly is the part # LC67VR.

expert reply by: Jameson C

0

Answer 1

We only have 2 options for replacement gas struts for awnings. The first is the Solera Gas Strut item #LC280343. This strut is 26" long and is rated at 124 lbs for short and flat awning arms. The second option is the one you were looking at…

view full answer...

Answer 2

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 3

Per Lippert, the inner arm 383152 is not available on its own, you must purchase the entire pitch arm which is the Solera 69" Standard Flat Awning Support Arm part #LC281154.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The LaSalle Bristol Cable-Actuated RV Waste Valve for Gray Water Tank #34466N11AB36GM is the best replacement for your 310115. This also fits a 1-1/2" pipe and has the same 36" cable length.

view full answer...

Answer 6

Normally you would need to measure your equalizer so we could find the best fit for your travel trailer. Lucky for you, you have a Grand Design and they actually list their parts online. Your 2021 Grand Design Imagine 2400BH has 35" axle spacing…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The ball on top of the suction mount of the #FOS05TASF is .85" in diameter. As far as the cables, 1 cable is used to install the monitor. The 12v plug on the monitor end installs into a cigarette lighter port on your vehicle. I went ahead and…

view full answer...

Answer 9

The biggest factor to consider when towing a long trailer with a short wheel base tow vehicle is trailer sway. There is no standard ratio for wheelbase to trailer length, but the general rule is a longer trailer and a shorter wheelbase will increase…

view full answer...

Answer 10

Yes! From the looks of your previous searches, you are referring to the etrailer eDream RV Mattress - Innerspring - 75" Long x 60" Wide #e94FR. We do carry a 80" x 60" version of the etrailer eDream. That is the etrailer eDream…

view full answer...

Answer 11

Both the MORryde Rubber Equalizers #MR87ZR and Dexter E-Z Flex Suspension Kit #K71-652-00 are achieving the same result. They are doing so with slightly different designs but end up with the same result. I recommend using the Dexter E-Z Flex…

view full answer...

Answer 12

I recommend the MORryde Suspension Upgrade Kit #MR46ZR for your 2021 Grand Design Imagine XLS 22RBE, as it includes all new wet bolts, bronze bushings, nuts, and shackle straps to replace your current bolts and straps. This will save you from having…

view full answer...

Replacement Arm Assembly for 63 inch Flat Solera Awning

Product Page this Question was Asked From

Continue Researching