What is the Inner/Outer Diameter of the Camco Replacement 90-Degree Exhaust Pipe?

Question

Question:

exhaust pipe Cam44812 24 x 6 What is the ID or OD measurement at the 6 end? thank you

asked by: Robert I

0

Expert Reply:

The Replacement 90-Degree Exhaust Pipe for Camco Gen-Turi RV Generator Exhaust System # CAM44812 you mention has an inner diameter of 1.53" and an outer diameter of 1.51".

expert reply by: Bryce D

0

Answer 1

For your generator exhaust, the Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe #CAM44812 is designed to be used with the Camco Gen-Turi RV Generator Exhaust System #CAM44461. With that being said, we have not tested the #CAM44812…

view full answer...

Answer 2

I went out to our warehouse and doublechecked the length myself and found the overall length of the Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe #CAM44812 to be 30" when including the bend. You are correct that the straight…

view full answer...

Answer 3

The Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe #CAM44812 has the same diameter aside from the shorter end where it gets larger to accept a 1-1/2" diameter pipe. You can to cut the longer end so that it is shorter and…

view full answer...

Answer 4

Here are the inner and outer dimensions for the Camco Gen-Turi items you asked about. Part #CAM44872 – OD is 2.94 inches and ID on the small end is 2.69 inches. Part #CAM44862 – OD is 1.51 inches and ID is 1.25 inches on the flared end. No dimensions…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

What is the Inner/Outer Diameter of the Camco Replacement 90-Degree Exhaust Pipe?

Product Page this Question was Asked From

Continue Researching