Can The Replacement Tail Clamp For Extang Trifecta 2.0 Be Unscrewed and Replaced As Only The Handle?

Question

Question:

Hi, can I disassemble the rear clamp on the Trifecta 2.0? I cant unscrew it and leave the barrel in the channel. If I can, I can use a replacement. Thanks

asked by: Jeff C

1

Helpful Expert Reply:

You are going to need to replace the Tail Clamp Assembly # EX31003005 as an entire part. The components inside the clamp are difficult to assemble if removed and you may not be able to get everything back together correctly. This is why Extang only offers the clamps as assemblies and not just the handle separately.

expert reply by: Bud M

1

Answer 1

I'm glad to hear that you received the Rear Tailgate Clamp, #EX31003005, for your Extang Trifecta 2.0 tonneau cover. I called Extang and discovered that they don't have any videos for replacing the rear clamp. But, they were kind enough to…

view full answer...

Answer 2

Typically when water starts to seep into a truck bed with a tonneau cover installed it's coming in from the cab side or through tiny openings at the tailgate. What you can do to try and prevent this with your cover like the Extang eMAX #EX72780…

view full answer...

Answer 3

I reached out to my contact at Extang and was told that air may be getting underneath the Extang Trifecta 2.0 Soft Tonneau Cover #EX92830. To fix this issue, drop the tailgate and look inside the bed to see if you can see light coming through in the…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The correct replacement clamp for the Extang Solid Fold 2.0/Trifecta 2.0 cover on your 2008 Toyota Tundra is part #EX31003005, and according to the instructions it will be compatible with the Deck Rail System on your truck bed.

view full answer...

Answer 7

I reached out to Extang directly regarding your inquiry on the Replacement Cab Clamp #EX1034. They advise to release the clamps, remove the tarp from the rails so that the frame loses enough tension to be pulled apart. Included is the tarp…

view full answer...

Answer 8

Yes, we sell both of the parts you are looking for in the attached photo. These two parts are the Replacement Clamps for Extang Trifecta Soft Tonneau Covers part #EX2244-0204 and the Replacement Tail Clamp Assembly for Extang Trifecta 2.0 Tonneau…

view full answer...

Answer 9

None of the methods are super easy. I'd recommend three though you have to remove hinges. This is least invasive, doesn't require cutting the cover, and also doesn't risk damaging cover.

view full answer...

Answer 10

While it can be difficult to get started on these the two panels will slide into the Replacement Tail Hinge for Extang Solid Fold 2.0 Hard Tonneau Cover part #EX83475-64. Of course there is the seal to get out of the way so you can begin sliding the…

view full answer...

Answer 11

I have a complete replacement option for you, but unfortunately Extang discontinued the Extang Solid Fold Tonneau Cover 56450 you have on your 2014 Chevrolet Silverado back in 2015 and no replacement parts are available any longer. For a replacement…

view full answer...