Correct Loading Ramp for Swagman E-Spec Bike Rack

Question

Question:

Will this ramp work with my Swagman E-Spec Bike Rack?

asked by: Mike C

0

Expert Reply:

The Loading Ramp for Swagman Skaha and Escapee Bike Racks # S59SR is only going to work with the Swagman Skaha and Escapee bike racks and will not work with your E-Spec bike rack.

Instead, you're going to want to check out the Swagman Ramp and Bridge for Swagman Current, E-Spec, and G10 Bike Racks # S32YR which is going to work with your E-Spec.

expert reply by: Bryce D

0

Answer 1

We do carry the Swagman Ramp and Bridge #S32YR for the Swagman Current Bike Rack #S64678. This will also fit the Swagman E-Spec #S94FR and G10 bike racks.

view full answer...

Answer 2

I reached out to Swagman who verified you are still able to use the Loading Ramp #S59SR with your Escapee Bike Rack #S39SR. They mentioned you will have a bit of a hump to get over when going from the rear wheel carrier to the front wheel carrier.

view full answer...

Answer 3

The Swagman Escapee Bike Rack #S39SR is a great solution for e-bikes that don't utilize a front fender. It doesn't come with a ramp but one can be added on: - Loading Ramp for Swagman Skaha and Escapee Bike Racks #S59SR I really like this…

view full answer...

Answer 4

I spoke with my contact at Swagman about the Swagman XC #S64650 and she said that the holes in the arm hook assembles actually is not for a padlock. The holes are what they use to hang those parts of the arms on when they are putting products on…

view full answer...

Answer 5

We do carry the Replacement Cable #S2005. This cable has the loop on one end and bolt hole on the other end of the 7' cable. It is constructed of 10mm braided steel cable. We do not have one 8-1/2' long like the Anti-Rattle Hitch Lock and…

view full answer...

Answer 6

The Swagman XC #S64650 actually has a threaded hitch pin to help eliminate movement of the bike rack in the Curt Trailer HItch #C12091 on your 2017 Ford Fusion. This means that if you are wanting to use a locking hitch pin you would need part #S64029…

view full answer...

Answer 7

Yep, there is indeed a loading ramp you can get that works with the Swagman Escapee RV Bike Rack for 2 Electric Bikes #S39SR. The correct part is the Loading Ramp #S59SR.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 12

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Correct Loading Ramp for Swagman E-Spec Bike Rack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching