Diagram of How Front Bracket of HappiJac Truck-Mounted Camper Tie-Downs LC182861 Installs

Question

Question:

I’m looking to get a picture of how the front brackets of #LC-182861 mount, and where on the truck they mount. I’m thinking of buying this kit, but won’t until I see how these front brackets mount. Thank you.

asked by: Dan K

0

Expert Reply:

I attached a diagram I got from the instructions that shows how the front bracket of the # LC182861 installs for you to check out.

expert reply by: Jameson C

0

Instalal Diagram
(click to enlarge)

Answer 1

The The Brophy Camper Tie Downs #TDSF, are a universal fit kit intended to fit as many trucks as possible. While there is nothing to say that it for sure fits, looking at your pictures it seems likely that it will work for your 1968 Ford F-250…

view full answer...

Answer 2

I went ahead and reached out to Torklift, and they confirmed what you need to in order to remove the gas tank cover on your vehicle to install the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLF2016. The cover drops down and gives you…

view full answer...

Answer 3

We do carry Torklift Tie Downs that fit your 2018 Chevy Silverado 2500HD short bed, double cab. For that you'd want the part #TLC2223 for the front and then for the rear #TLC3215. These are custom fit for your truck and by far the best…

view full answer...

Answer 4

We do have no-drill camper tie down kits that fit your 2014 Chevy Silverado from the brand Torklift but we do not have any from Happijac as they all require drilling. Since there are several variations of your truck and the Torklift fits are very…

view full answer...

Answer 5

To install the Replacement Anchor Bolt for HappiJac Truck #LC182852 for the HappiJac Truck-Mounted Camper Tie-Downs #LC182861 follow the instructions below and use the reference picture attached: 1. You'll start by marking a center point…

view full answer...

Answer 6

The HappiJac Camper Tie-Downs #LC182860 you were looking at unfortunately are not a fit for your 1997 Ford F-350 XLT. Happijac does however offer a fit with the HappiJac Camper Tie-Downs #LC182910-182971. This system mounts in the bed and on the rear…

view full answer...

Answer 7

Motor and Switch Kit for Stromberg Carlson Landing Gear - 5,500 lbs #LG-217884 only will use one switch. If you were to use two motors, then dual switches would be used. I've attached a diagram to assist. The input wires from the battery can be…

view full answer...

Answer 8

You are correct the HappiJac Camper Tie-Downs #LC182904-182971 are the correct kit for your 2013 GMC Sierra 3500 with a regular cab and 8' bed. I would highly recommend looking at the Torklift Front #TLC2215 and Rear #TLC3212 as a better option…

view full answer...

Answer 9

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 10

Unfortunately we do not have a video of the HappiJac Truck-Mounted Camper Tie-Downs #LC184089 being installed. The Rear anchors are installed in the end of the bumper. There is no precise mounting location since a variety of bumpers may be installed.…

view full answer...

Answer 11

Yes, for your 2001 Ford F-250 crew cab, long bed, diesel, with removed side steps, and an aftermarket hitch the correct tie downs are the part #TLF2011 and #TLR3500 that you referenced.

view full answer...

Diagram of How Front Bracket of HappiJac Truck-Mounted Camper Tie-Downs LC182861 Installs

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching