Installation of the Rear Bumper Tie Downs of the HappiJac Truck-Mounted Camper Tie-Downs
Question:
Is there any videos i can look up on exactly how the rear tie downs are installed ? Its the only part of the kit that i have read complaints about on third party RV forums. I see there appears to be some kind of braces for the rear bumper mounting points that i assume attach unseen on the inside of the bumper. But all i can gleen from the pictures is that you drill a hole in the already very flimsy chrome bumper and tighten a nut haha. Thank you!
asked by: Jay B
Expert Reply:
Unfortunately we do not have a video of the HappiJac Truck-Mounted Camper Tie-Downs # LC184089 being installed. The Rear anchors are installed in the end of the bumper. There is no precise mounting location since a variety of bumpers may be installed. The general guidelines are as follows:
1. Mounting location should be as flat & vertical as possible.
2. Be sure no moldings or bumper caps interfere with
the removable coupler.
3. Check back side of selected mounting location to ensure
adequate access for tightening nut.
4. Choose a location approx.2/3 back from the front edge
of the bumper. Center punch and drill a small pilot hole, then
enlarge to 1/2”.
5. Install Anchor Bolt with 2” fender washer, lock washer & nut.
The bumper is then supported by rear bumper braces.
Product Page this Question was Asked From
HappiJac Camper Tie-Downs - Custom Bed and Bumper Mount - Front and Rear
- Camper Tie-Downs
- Front and Rear Tie-Downs
- Bed-Mounted
- Frame-Mounted
- Custom Fit
- Steel
- HappiJac
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Camper Tie-Downs
- Shop: HappiJac Camper Tie-Downs - Custom Bed and Bumper Mount - Front and Rear
- Shop: Brophy Stake Pocket Mounted Camper Tie-Downs - Bed Mount - Qty 4
- Shop: Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
- Video: Brophy Camper Hold Downs Review
- Shop: Brophy Cable Camper Jacks - 57" Max Lift Height - 1,000 lbs - Qty 2
- Shop: HappiJac Original Turnbuckles for Camper Tie-Downs - Stainless Steel - Qty 4
- Shop: Brophy Slide In Camper Tie-Downs - Extra Clearance - No Drill Bed Mount - Qty 4
- Shop: HappiJac Camper Tie-Downs - Custom Bed and Bumper Mount - Front and Rear
- Q&A: Instructions For HappiJac Truck-Mounted Camper Tie-Downs # LC184089
- Search Results: brophy
- Search Results: turn buckle
- Video: Brophy Camper Tie-Downs - Turnbuckles - TDHP Review
- Video: Review of Brophy Camper Jacks - Tall Truck Bed Camper Jack - CJ74H
- Q&A: Will Cable Camper Jacks Flip Truck Camper When Being Used
- Q&A: How Long Could 100 Amp Hour Battery Power 5 Amp Roof Vent
- Article: Determining Trailer Tongue Weight
- Shop: Vehicle Cargo Control
- Shop: Tonneau Cover
- Shop: Trim Kits
- Shop: Vehicle Seat Covers
- Video: Review of TorkLift Camper Tie-Downs - Front Tie-Downs - TLD2140
- Article: Stability Control for Heavy Duty Vehicles
- Q&A: Recommended TorkLift Tie-Downs For A 2023 Ram 2500 Crew Cab 6-1/2' Bed
- Article: How to Mount a Truck Bed Camper
- Shop: Suspension Enhancement
- Q&A: Installation Instructions on Front and Rear TorkLift Custom Frame Mounted Camper Tie Downs
- Shop: Trailer Hitch
- Search Results: slide in camper tie down
- Q&A: Will Brophy Camper Tie-Downs Work With Composite Bed On 2013 Toyota Tacoma
Ellen
4/26/2024
I just ordered the rear mount happijac for my 2004 Toyota Tacoma bumper. Reading over these directions this is the first time I have heard about the rear bumper brace. Can you direct me to this part? Thanks