Replacement For WiSight Voyager Camera System

Question

Question:

Will this camera work with my voyager model #wvom43 monitor? ASA64YR

asked by: Rob

0

Expert Reply:

It is not as you have a first version Voyager WiSight camera system; this is only compatible with the 2.0 systems and the first generation cameras are not available any longer so you'll need to replace your system with the Voyager WiSight 2.0 Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 4.3" Screen # ASA84YR.

expert reply by: Kyle S

0

Answer 1

There are a few lift kits available for torsion axle trailers, but they vary by weight capacity and manufacturer. I can not find the exact axles that are on your 2017.5 Lance 1995 travel trailer, but if you look at the axle tag it will let you know.…

view full answer...

Answer 2

Thanks for reaching out, i have a couple things for you to do. Let me explain below: *12V PWM Filter for RV Backup Camera Systems - Hardwire #VGR64VR. The newer GMC vehicles use PWM(Pulse With Modulation) in their electrical systems. The Furrion…

view full answer...

Answer 3

Your Voyager WiSight 2.0 Wireless RV Backup Camera System #ASA84YR most likely is getting the correct amount of voltage to it causing the signal lose you've been experiencing. I recommend splicing in the PWM Filter #VGR64VR behind your camera to…

view full answer...

Answer 4

You will need to replace your entire system as the Voyager WiSight WVOM541AP is obsolete. I recommend upgrading to the Voyager WiSight 2.0 Wireless Backup Camera System #ASA37YR. While these are both WiSight systems the 2.0 and original WiSight are…

view full answer...

Answer 5

The Air Spring #AL50217 has a design height of 5-1/2". This is the height the air spring is designed to have between the mounting brackets at stock, unloaded weight.

view full answer...

Answer 6

The Voyager WiSight 2.0 you referred to, part WVSXS43 which we offer as part #ASA84YR isn't compatible with the first generation 1.0 system. The good news is that installing the new system will be pretty simple. The new camera can use the same…

view full answer...

Answer 7

There is one option that has the right dimensions to replace the Atwood 87891, which is a handle from Stromberg Carlson: - Replacement Crank Handle for Stromberg Carlson Landing Gear #LG-119226 The metal shaft where it attaches to the jack has an…

view full answer...

Answer 8

I have done a bit of research and it sounds like you need the hose that goes from the propane bottle to the regulator. We have 3 different lengths of the MB Sturgis Propane Hose Assembly. We have 12", 15", and 20" lengths. - MB Sturgis…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

More than likely you will need a new system. The WVOM541AP was discontinued. The new monitor is the Voyager WiSight 2.0 Wireless RV Backup Camera Monitor #ASA27FR, but this monitor only works with the WiSight 2.0 systems. You likely have the original…

view full answer...

Answer 11

Yes, you can remove the Shark Fin Camera Mounting Bracket #FRCBRKT-BL which includes the wiring from your 2024 Forest River Flagstaff Super Lite 26FKBS for a Voyager system. The Kit #ASA24YR you found is specifically designed for trailers pre-wired…

view full answer...

Replacement For WiSight Voyager Camera System

Product Page this Question was Asked From

Continue Researching