Replacement Axle Option For a 1996 Dutchmen 1204 Pop Up Camper With Torsion Axle

Question

Question:

Hi, I’m needing to replace the torsion axle on my 1996 Dutchmen 1204. Can you help me determine which axle I should get? Are they standard, or do I have to do some measurements to get the right one? Thanks

asked by: Patrick M

0

Expert Reply:

For you 1996 Dutchmen 1204 we will only carry an axle system like the Timbren Axle-Less Trailer Suspension # A35RS545. We do not carry torsion axles at this time. To determine if this can be used on your camper you will need to measure the distance from the hub face to the outside of the frame along with the height of the axle center line from the bottom of the frame. This particular system has a hub face that will sit 6" from the frame with an axle centerline 3-13/16" below the frame with no weight on the suspension. The suspension will compress 1-3/4" bringing you down to 2-1/16" when compressed. Please let me know if you find you have different measurements and this system is not compatible.

expert reply by: Bud M

0

Answer 1

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

We have one option that will work for you. The Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ uses inner bearing #L68149 and outer bearing #LM67048 so it would work perfectly on your spindle.…

view full answer...

Answer 12

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Replacement Axle Option For a 1996 Dutchmen 1204 Pop Up Camper With Torsion Axle

Product Page this Question was Asked From

Continue Researching