Hardware Size Needed for TorkLift GlowStep Revolution Scissor Steps

Question

Question:

I have 2017 Lance 1995, to add the Torklift TLA8102 steps. I got the rivets out that hold the old steps. Rivets only have 1/4 hole. Do i need to drill bigger holes for the new steps?

asked by: William J

0

Expert Reply:

The TorkLift GlowStep Revolution Scissor Steps part # TLA8102 attach using 3/8" hardware so you'll need a .375" hole to secure them. The step brackets install into outrigger brackets already on the trailer under the door. I have attached a photo below that shows this.

expert reply by: Conner L

0

Hardware Size Needed for TorkLift GlowStep Revolution Scissor Steps
(click to enlarge)

Answer 1

The TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear #TLA8102 have a height of 16-1/2" from the top of the mounting bracket to the bottom of the steps when fully retracted. I've attached a photo of this to give you a visual.

view full answer...

Answer 2

Step #SMFP-2100 is supposed to mount up to factory holes on the bottom of the frame or it can be welded to the frame. For nuts and bolts use #LC118155-72 if you don't already have some from the old steps. For welding the installation should be…

view full answer...

Answer 3

The TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 3 Steps - 375 lbs - Black Bracket #TLA7833 has a weight capacity of 375 lbs. The mounting bracket is 21.5 inches wide by 12.5 inches tall and 8.5 inches deep. It is designed for…

view full answer...

Answer 4

The Torklift Glowstep Revolution Scissor Steps #TLA8102 would be the correct fit for your 2021 Lance model 1995 travel trailer if your entry height was between 18-1/2" to 28" and you had room for the mounting bracket width of 25-1/2…

view full answer...

Answer 5

Flexco Manual Pull-Out Steps for RVs - Double - 7-7/8" Drop/Rise - 24" Wide - 350 lbs #SMFP-2100 are from Stromberg-Carlson and are Flexco model steps. So in other words they are one in the same. I included some pictures showing dimensions…

view full answer...

Answer 6

I spoke to my Lippert contact and they informed me that the mounting width of the #LC3725791 is 24-5/8 inches center on center and 25-9/16 inches over all. I have attached an image of the mounting holes for you to check out. The width of the step is…

view full answer...

Answer 7

Since your door is 30 inches from the ground the correct MORryde Step Above you'd need to use is the part #MR98RR which works with that height and also fits doorway widths between 23-3/4 and 26-1/4 inches.

view full answer...

Answer 8

For the 25" height and 25" doorway width measurements you need the MORryde StepAbove RV Steps #MR26RR. This has an entry height (ground to threshold) range of 25" - 29" and a doorway width (inside flange to inside flange) range of…

view full answer...

Answer 9

The SolidStep Manual Fold-Down Steps for 25" - 28-7/8" Wide RV Door Frames - Double - Aluminum, part #LC733931, will fit your RV door without any issues. These steps will fit doorways from 25" wide up to 28-7/8". The 1/4"…

view full answer...

Answer 10

In order for the MORryde StepAbove #MR26RR to fold down you'd need to have between 25 and 29 inches from the threshold to the ground on your RV.

view full answer...

Answer 11

To solve your step issue I recommend the MORryde StepAbove Fold-Down Steps for 23-3/4" to 26-1/4" RV Door Frames - 8" Drop Item #MR98RR. This will bolt right onto the bottom portion of the door frame instead of the sides and has…

view full answer...

Answer 12

For a mounting bracket width of 25" we only have a one-step RV Step #SMFP-1100. What you can do instead is install an a fold-down step like the MORryde StepAbove RV Steps - 2 Steps Item #MR26RR. It fits a doorway width of 23-3/4" -…

view full answer...

Hardware Size Needed for TorkLift GlowStep Revolution Scissor Steps

Product Page this Question was Asked From

Continue Researching