Oil Bath Cap for Dexter Hub 8-248

Question

Question:

I have a Dexter 8-248 hub and am looking for an oil bath cap for it, are there any available for this model?

asked by: Scott

0

Expert Reply:

Yes, since the hub bore of a Dexter 8-248 hub is 1.98 inch the correct oil bath conversion cap would be the part # xlprolube1980.

expert reply by: Jameson C

0

Answer 1

We don't have the UFP Brand, but I can give you some compatible parts. For your trailer hubs with rotor, I recommend the Kodiak 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Dacromet - 3,500 lbs #KHR10D. You will need grease seal…

view full answer...

Answer 2

In your oil bath-type hubs you will want to use any 80- or 90-weight synthetic gear oil. My contact at Kodiak confirmed that the brand of oil is not important but that use of a synthetic oil in this viscosity range is what matters. As it happens…

view full answer...

Answer 3

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 6

The seals #9103309 and #GS-2250DL have the same inner and outer diameters (2.250" ID and 3.376" OD) but they are used for different applications. Use the seal #9103309 if you have an oil bath setup but you'll want to use the seal…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Oil Bath Cap for Dexter Hub 8-248

Product Page this Question was Asked From

Continue Researching