Replacement Swivel Collars for Roadmaster Falcon 2 All Terrain Tow Bar

Question

Question:

I own a falcon 2 all terrain 047280 and I am looking at replacing the round Nuts and swivel collars. Thanks

asked by: Rick L

1

Helpful Expert Reply:

For your Roadmaster Falcon 2 All Terrain we have replacement swivel collars with the part # RM-9200-6. This comes with nuts as well.

expert reply by: Jameson C

1

Answer 1

So our base plate kit manufacturers will create fits for vehicles as long as their is demand for them. So for your 2012 Honda Accord Coupe we have the Roadmaster base plate kit part #521565-1 as a confirmed fit. Sometimes manufacturers will state…

view full answer...

Answer 2

I did some research and you'll want to confirm this in the owner's manual of your 2013 Honda Accord, but it appears that all models of the Accord must be towed on a tow dolly in the same manner as your 2009 Altima. Unfortunately it appears…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Replacement Swivel Collars for Roadmaster Falcon 2 All Terrain Tow Bar

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching