Replacement Motor For A MaxxAir MaxxFan Deluxe

Question

Question:

Can i get part a Maxxair deluxe fan? I need the motor that opens and close the vent pn:10-20270 12vdc 40.5 rpm

asked by: Patrick

0

Expert Reply:

Yes, the part number you provided is the Replacement Lift Motor for Maxx Fan Plus Roof Vent # MA10-20270. This motor fits the following models:

MA00-4501K
MA00-04500K
MA00-07000K
MA00-07500K

If you have a different model then let me know and I can ensure that you're getting the correct replacement.

expert reply by: Kevin C

0

Answer 1

The Thule Epos #TH99XE will work with a car, truck, SUV, or van. Unfortunately, it will not work with a motorhome or trailer. For a 2-bike rack that can handle heavy bikes and is motorhome compatible I recommend the Hollywood Racks RV Rider Bike Rack…

view full answer...

Answer 2

The model number for fans such as the MaxxAir MaxxFan Mini Roof Vent, #MA00-04401M is listed on the upper side of the assembly itself. Please see the attached image. You will best identify this by opening the vent and climbing on top of the RV.…

view full answer...

Answer 3

While I don't have direct instructions about replacing the Lift Motor #MA10-20270, I can tell you how to gain access to the lift motor. You want to start by removing the screen on your MaxxFan. This is done by rotating the 4 locking tabs 180…

view full answer...

Answer 4

The correct replacement lift motor for a Maxxair Vent Fan 4751KS is the Replacement Lift Motor for Maxx Fan Plus Roof Vent part #MA10-20270.

view full answer...

Answer 5

If you have the MaxxFan part #MA00-04000K you need the replacement circuit board part #MA10A21276K as yours is damaged which is what's causing the strange behavior of yours.

view full answer...

Answer 6

Thanks for getting me the number on your motor as I can tell from that you need the part #MA10-20968.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Replacement Motor For A MaxxAir MaxxFan Deluxe

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching