Aries Automotive Grille Guard Hardware Kit for 2003 Chevy Silverado

Question

Question:

Do you have a brush guard mounting bracket kit for a 2003 Chevrolet Silverado 4wd?

asked by: Jerod W

0

Expert Reply:

For a 2003 Chevy Silverado 1500 you'd want the # AABRKT-4059.

expert reply by: Jameson C

0

Answer 1

If you had an Aries Grille Guard for your 2003 Chevy Silverado 1500 it would have been part #AA4059 so the correct replacement bracket kit you'd need is the #AABRKT-4059.

view full answer...

Answer 2

In order to replace the mounting hardware on a Westin Sportsman Grille Guard #40-1175 you'll need to use the Replacement Mounting Kit for Sportsman Grille Guard #40-117PK. This hardware works with both the #40-1175 and the #45-1770 Sportsman…

view full answer...

Answer 3

I have a solution for you, but the #57-378PK is not designed for a Westin Grille Guard that fits on the 2003 Chevy Silverado 2500. Instead, you most likely have a Westin Sportsman Grille Guard part #45-1240 or 40-1245. For those grille guards the…

view full answer...

Answer 4

It sounds like you're looking for a replacement installation kit for a Westin Sportsman Grille Guard that fits a 2009 Ford F-150. If so, the Replacement Mounting Kit for Westin Sportsman Grille Guard #40-250PK is the correct kit to install the…

view full answer...

Answer 5

The correct part number for a Westin Grille Guard for your 2004 Chevy Silverado 2500HD is the part #40-1245.

view full answer...

Answer 6

I have an alternate solution for you but we do not currently have the mounting hardware/brackets for your Aries grille guard. I contacted the manufacturer about getting them added for you. Unfortunately, the mounting hardware/brackets are no longer…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Aries Automotive Grille Guard Hardware Kit for 2003 Chevy Silverado

Product Page this Question was Asked From

Continue Researching