Mounting Bolt Hole Pattern For The Bulldog Powered Drive Trailer Jack # BD500199

Question

Question:

Would like to know the bolt pattern diagram? and diameter of the top mounting plate. My ATC trailer is 3inch O.C. from the frontfoot to the rear two bolts, but 3.25inch O.C. between the rear two bolts. Thank you.

asked by: Mark F

0

Expert Reply:

The Bulldog Powered Drive Trailer Jack # BD500199 has two sets of mounting holes on its mounting flange that are approximately 3.47" apart center-to-center. The two sets are spaced apart approximately 1" center-to-center.

expert reply by: Kevin C

0

BD500199 Mounting Hole Pattern
(click to enlarge)

Answer 1

I do have a recommendation for you rather than replacing your Jack #EJ-3520-BBX with one like the Bulldog #BD500199 which can be mounted sideways. You can switch to a longer Ball Mount #BH20 or Shank #EQ90-02-4600 to move your hitch ball further…

view full answer...

Answer 2

Douglas, you can use the Electric Jack w/ Footplate and 7-Way Plug #EJ-3527-BBX for an electric jack or the Buyers Products A-Frame Jack w/ Support Foot #3370091265 for an manual option. Both of these jacks would work great to replace the jack you…

view full answer...

Answer 3

There are pros and cons to both Husky and Bulldog electric trailer jacks. My favorite Husky jack is the Husky Brute Electric Trailer Jack part #HT87247 and my favorite Bulldog jack is the Bulldog Powered-Drive Trailer Jack part #BD500187. The reason…

view full answer...

Answer 4

The closest thing we have to a 2" x 2" bumper is the Rubber Bumper for Enclosed Trailer Ramp Door #37210715 you looked at. This has a 2-1/2" diameter with a height of 1" and a 3/8" mounting hole.

view full answer...

Answer 5

Both Firestone Ride-Rite kits are good options for your 2024 Ford F-250 Super Duty 4WD, but I like to recommend the 7,500 lb #F95FV rating over the 5,000 lb Rating #F35FV simply because it means the air bags can be used for the same application but…

view full answer...

Answer 6

If you already have a seal that you're replacing then you want to get a seal that's a similar size, otherwise if it's a brand new application then I recommend trying to find the depth of the gap and choosing a seal slightly taller since…

view full answer...

Answer 7

I recommend going with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL89DQ for hauling around an in-bed camper with your 2024 Ford F-350 Super Duty. I really like this kit because it has the higher 7,500 lb rating (which you don't…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Mounting Bolt Hole Pattern For The Bulldog Powered Drive Trailer Jack # BD500199

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching