Is Mounting Bracket of Voyager WiSight 2.0 The Same As 1.0 Kit

Question

Question:

In addition to the Voyager 2.0 using the existing power supply for the Voyager 1.0, do you know if the Voyager 2.0 Camera system mounts to the Voyager 1.0 bracket?

asked by: Bob

0

Expert Reply:

The mounting brackets between the WiSight 1.0 and the 2.0 like the part # ASA84YR are different so with this kit you would not be able to reuse them.

expert reply by: Jameson C

0

Answer 1

For your Replacement Voyager WiSight 2.0 Wireless RV Backup Camera Monitor #ASA27FR (WVSXM70), you can use the Replacement Voyager WiSight 2.0 Wireless RV Backup Camera with Low Light Assist #ASA64YR. These cameras do have the 4 pin connector that…

view full answer...

Answer 2

It is not as you have a first version Voyager WiSight camera system; this is only compatible with the 2.0 systems and the first generation cameras are not available any longer so you'll need to replace your system with the Voyager WiSight 2.0…

view full answer...

Answer 3

If you've already checked all your connections and power source then it leads me to believe you might be using first gen and 2nd gen equipment together. The WVOS43 is the first generation of the WiSight camera systems so if you were using this…

view full answer...

Answer 4

The correct replacement for a Kwikee Step Motor 369545 is the Replacement Motor for Kwikee Electric RV Steps part #LC379147.

view full answer...

Answer 5

From what I can find the dimensions of the Apollo Halftime RV Microwave AAC240TRB are 12" T x 20.6" W x 20.5" D. If this is the case with yours then the closest option we have available size-wise would be the Furrion Standard RV…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Is Mounting Bracket of Voyager WiSight 2.0 The Same As 1.0 Kit

Product Page this Question was Asked From

Continue Researching