Safety Chain Loops For Elite Series Puck Adapters

Question

Question:

Which safety chain loops can I purchase that will fit the RP30149 extension kit? I plan to weld and support the puck pockets on a flatbed Im building.

asked by: Ron W

0

Expert Reply:

The safety chain loops you can use with the Reese Elite Series 5th Wheel Rail Puck Adapters for Plastic Truck Bed Liner RP30149 are the Curt Safety Chain Loops for Factory Chevy, Ford, GMC, and Nissan Underbed Gooseneck Trailer Hitch # C60691.

expert reply by: Kyle S

0

Answer 1

The shaft on which the crank attaches to for the Pro Series Square Jack, #PS1400950376, measures 1 inch in diameter. I have also included a dimensional diagram for the jack for you to view.

view full answer...

Answer 2

The only trailer tire sensors that will work with the factory TPMS on your 2021 GMC Sierra 3500HD Denali is the GM kit 85110397 that is sold through GM. These sensors will need to replace the valve stems on your trailer wheels. I recommend staying…

view full answer...

Answer 3

Yes, the gooseneck hitch balls for the factory prep packages are the same for Ram and Ford. If you need a new hitch ball for either of these systems than you can use the Curt Pop-In Ball part #C60601 or the Reese Pop-In Ball part #RP19311.

view full answer...

Answer 4

Yes, the pop-in style gooseneck trailer hitch balls are cross compatible between the different factory puck systems from Ford, Ram, GM, and Nissan. For this, we have a few options such as the Curt Pop-In Ball part #C60629 which has a rise built-in…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Safety Chain Loops For Elite Series Puck Adapters

Product Page this Question was Asked From

Continue Researching