What's The Mounting Hole Dimensions On Curt QuickPin Coupler C82CR?

Question

Question:

Hi, What is the width between the mounting bolts?

asked by: Nick

0

Expert Reply:

On the Curt Coupler # C82CR the two mounting holes are 3" apart on center which you can see in the below diagram.

I included a video of AJ installing this coupler for you to check out as well.

expert reply by: Samuel C

0

Mounting Hole Dimensions Of Curt QuickPin Coupler C82CR
(click to enlarge)

Answer 1

Yes, you can install a B and W Gooseneck Hitch part #BWGNRK1108 in your 2002 Ford F-250 that has the Firestone air bag kit as long as the kit you have is part #F2550 installed as this Firestone kit was designed to allow in-bed hitches like this to…

view full answer...

Answer 2

The A-Frame Trailer Coupler part #CA-5400-B is a full replacement and the only way I know to repair it when it is broken. The Repair Kit for etrailer and Ram A-Frame Couplers part #CA-5100-RK is designed for original trigger latch couplers…

view full answer...

Answer 3

To adjust the hitch latch on your trailer's coupler, you will want to adjust the nut at the bottom of the latch. This nut will be tightened or loosened depending on what you need for your coupler. I have attached a diagram showing you the…

view full answer...

Answer 4

To help alleviate the back and forth chucking you are experiencing with your 2 inch receiver there are a couple of things I recommend doing. First is to use a cushioned ball mount, the Convert-A-Ball, which is designed to reduce this type of…

view full answer...

Answer 5

I contacted Malone and the Malone XtraLight Trailer (MPG525) is not compatible with Crossbars for Malone MicroSport Trailers - 78" Long part #MPG4001. The only trailer that can use the longer cross bars is the Malone Microsport trailers…

view full answer...

Answer 6

The Rhino-Rack Artificial Rain Gutters #739A are a universal fit since you'd be drilling through the wall of the trailer and bolting them in place. The only issue you might have is just with the bolt length. If the wall is too thick then…

view full answer...

Answer 7

There are a couple of different ways you can lock the Curt QuickPin No-Latch Trailer Coupler for 2" Ball, either with a standard coupler lock, or you can use a 1/2 inch diameter hitch pin lock, since that is the same size as the pin and…

view full answer...

Answer 8

The Add-On Receiver for Blue Ox Adjustable 2" Drop Hitch Receiver #BLU94TR has a towing capacity of 10,000 lbs and a tongue weight capacity of 1,000 lb.

view full answer...

Answer 9

I do have an option for you but roof rails won't work very well on a teardrop trailer, even if you were able to get the rails to conform, it's likely the accessories would bind due to the steep angles. Instead, you will need to use…

view full answer...

Answer 10

Yes, it will since your truck is a 2022! The 5" Offset Gen-Y Hitch Gooseneck Trailer Hitch item #GY55XR is designed to work in the 2020 and newer Silverado and Sierra's with the GM factory puck system. It will push the connection point for…

view full answer...

Answer 11

All Bulletproof Hitch products, including the #358smallshackle are sourced and made here in the United States. Their headquarters is in Bradenton, Florida.

view full answer...

Answer 12

The outside diameter of the Wire - Jacketed 6-Wire - per Foot #DW04906-1 is 1/2" including the vinyl jacket.

view full answer...

What's The Mounting Hole Dimensions On Curt QuickPin Coupler C82CR?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching