Fit of Curt Class I Receiver Hitch on 2012 Honda Accord Coupe
Question:
I saw somewhere where this fits up to 2012 Accord Sedan, but only up to 2010 Accord Coupe. Is this true? I have a 2012 Accord Coupe and want to make sure this Curt 110853 will be ok.
asked by: Kurt T
Expert Reply:
The Curt Class I hitch receiver, part # C11085 is compatible with 2008-2012 Accord Sedan and Coupe models. I confirmed this by phoning my Curt representative who assured me that the # C11085 will indeed fit your 2012 Accord Coupe.
If you will be towing with your hitch, you might need the following accessories:
Curt Class II Drawbar, part # C45521
Pin and Clip, part # F-4
Trailer Wiring Harness w/ 4-Pole Trailer Connector, part # 118420
1-7/8 Inch Trailer Ball, part # 19256
2 Inch Trailer Ball, part # 19258
I have linked you to an install video showing the hitch being installed on a 2011 Accord 4dr Sedan. The procedure for your 2012 Coupe would be identical. I have also linked you to a video for the wiring harness install.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Is Ground Clearance on a 2008 Honda Accord Lost with Hitch Installation
- Article: Best Bike Racks for Electric Bikes
- Q&A: Curt Trailer Hitch vs. Draw-Tite Trailer Hitch on 2020 Ford Escape
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Difference Between 2 Curt Trailer Hitch Receivers that Fit the 2009 Honda Accord
- Q&A: 2011 Honda Odyssey Touring Control Arm Bolt Torque Spec when Installing Air Suspension Enhancement
- Q&A: Draw-Tite vs. Curt Trailer Hitch For 2023 Kia Sportage
- Q&A: Recommended Receiver Hitch to Carry 2 Bike Rack on 2010 Acura TL
- Article: Replacing RV Awning Fabric: Your Step-by-Step DIY Guide
- Article: Hitch Adapters and Extenders
- Article: Trailer Lighting Requirements
- Article: Trailer Hitch Receiver Sizes
- Article: Best Bike Racks for Mountain Bikes (2023)