Recommended Replacement 5-Pin Wishbone Harness for a Boat Trailer

Question

Question:

Looking for a Boat Trailer 6 wire, 14 AWG, 5 pin wiring plug around 5 ft. long.

asked by: Willard T

0

Expert Reply:

What you're looking for is the 25 Ft 5-Way Trailer Wiring Harness # A25W5B. This is the 5-pin connector made of 16-18 AWG wires.

I know you were looking for only a 5' section, however the odds are that if you're just needing a small section you likely have other damaged wiring down the line somewhere, and should probably replace the entire harness.

Attached is an installation video for you to check out as well.

expert reply by: Bryce D

0

Answer 1

While tinned wiring is the norm when it comes to interior wiring on boats, boat trailers see a minimal amount of water compared to the actual boats. They do use a tin coating on the pins that are the parts of a wiring harness like the Wesbar 5-Pole…

view full answer...

Answer 2

The trailer wiring we offer like part #A40W5B, is designed to be used as a 5-wire harness, and works well with a trailer that has a surge coupler. The wires used in this harness are 16 gauge except the blue brake wire which is 18 gauge, and designed…

view full answer...

Answer 3

The Hopkins 5-Way Flat Connector #HM47913 you referenced has a 18 gauge wire for all but the ground wire, which is 16 gauge.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Recommended Replacement 5-Pin Wishbone Harness for a Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching