Is There a Replacement Monitor for the Voyager WV0S511 Camera System

Question

Question:

Need monitor for Voyager WV0S511. Is this compatible? Used on 2016 Lance 995 truck camper

asked by: Andy R

1

Helpful Expert Reply:

I spoke with Voyager about the Voyager Monitor WV0S511 and they informed me that this is no longer available and there is no direct replacement for this that will allow you to use your existing camera/cameras. Therefore, it will need to be replaced and for this they recommended the Voyager WiSight 2.0 Wireless RV Backup Camera System part # ASA57YR which is a wireless system so there is no wires run between the camera and monitor.

expert reply by: Conner L

1

Answer 1

The distance from the rearmost hitch pin hole of the Reese hitch extender part #RP45292 to the back of the extender is 6 inches which you can use to determine if that would hit your spare or not. This was designed to be trimmed down in length though…

view full answer...

Answer 2

The Hitch Box Extension and Reducer for Titan 2-1/2" Trailer Hitches, 24" - 34" Long #RP45292 or the Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches - 24" to 34" Long #C45048 will work for your truck and…

view full answer...

Answer 3

I have a complete replacement camera system option for you, but since your current camera system is no longer made there are no replacement cameras available that use your same monitor. I recommend replacing it with the Voyager WiSight 2.0 Wireless…

view full answer...

Answer 4

The Voyager Wisight systems are the current Voyager camera systems for RVs like with the part #ASA37YR for an RV that was pre-wired for a Voyager system or part #ASA57YR for one that was not which includes the wiring.

view full answer...

Answer 5

The Replacement Voyager WiSight 2.0 Wireless RV Backup Camera w/ Night Vision for Prewired System #ASA74YR, which is the WVSXP43 camera, is the camera that comes with the: -Voyager WiSight 2.0 Wireless Backup Camera System w/ Night Vision for…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Is There a Replacement Monitor for the Voyager WV0S511 Camera System

Product Page this Question was Asked From

Continue Researching