Recommended Black Nerf Bars for 1987 Ford Bronco

Question

Question:

Looking for solid black satin nerf bars and it looks like they need to attach to the frame any recommendations?

asked by: Jim B

0

Expert Reply:

We do have some great nerf bars options for a 1987 Ford Bronco, I recommend the Westin E-Series Round Nerf Bars part # 23-0535 which have a black finish and 3" wide steps for help getting in/out of the vehicle. They feature a bolt-on install with no drilling required. The steps tie into both the frame and rocker panel which you can see in the photo below.

expert reply by: Conner L

0

Recommended Black Nerf Bars for 1987 Ford Bronco
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 3

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 4

It sounds like the 2022 Chevy Silverado 3500 you are getting has the short bed. In that case, yes, you definitely want the sliding 5th wheel hitch for clearance. The good news is you will not need to purchase the entire B&W Companion…

view full answer...

Answer 5

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 6

Based on the information you gave, although I can't help with the axle (other than to state it is a 3,500 lbs axle). Dexter mobile home axles were designed for one time use and weren't really documented for replacement parts, but…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…

view full answer...

Answer 8

M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while 1/2" threads are going to be 0.500" in diameter. We currently only have…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 12

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Recommended Black Nerf Bars for 1987 Ford Bronco

Product Page this Question was Asked From

Continue Researching