Replacement Grease Cap for 1195 Haul-Master Trailer From Harbor Freight

Question

Question:

Do you have the dust cover wheel bearing cap for the 1195# Harbor freight Hual Master trailer?

asked by: Clayton P

0

Expert Reply:

Your 1195 Haul-Master trailer should have a BT8 spindle which means you need the kit # RG04-020 for standard caps, the kit # RG04-040 for EZ Lube caps, or the kit # BB1980A which is the Bearing Buddy kit with the auto check in place.

Attached is a video for you to check out.

expert reply by: Jon G

0

Answer 1

You would need to measure the inside diameter of the hub opening to determine which cap size is needed. You would want to choose a cap whose outside diameter matches the inside diameter of the hub. Some of the most common sizes are 1.980 inch, 1.986…

view full answer...

Answer 2

We don't offer a grease cap with a diameter between 1.99 and 2.251 inches. The bearing reference number is stamped into the bearing cage, as shown in the photo I've provided. If I knew the bearing number, I can determine which race is used.…

view full answer...

Answer 3

You would need to measure the inside diameter of the hub opening to determine which cap size is needed. You would want to choose a cap whose outside diameter matches the inside diameter of the hub. Some of the most common sizes are 1.980 inch, 1.986…

view full answer...

Answer 4

You can measure either the outer diameter of the part of the dust cap that fits into the hub OR the inner diameter of the hub where the dust cap goes using calipers such as #PTW80157. Calipers are needed because the measurement has to be as accurate…

view full answer...

Answer 5

The next largest size is #RG04-040 which has an OD of 1.99 inches. If you can provide me with the reference number from your outer wheel bearing, I'd be happy to check into the availability of a suitable grease cap.

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

I am happy to help you figure out which dust cap you need for the Haul Master utility trailer model 90154 however, I was not able to find any information about the wheels on your utility trailer. To get the correct sized dust cap you can simply…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Replacement Grease Cap for 1195 Haul-Master Trailer From Harbor Freight

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching