Replacement Lockable Knob for Thule Spare Me Spare Tire Bike Rack

Question

Question:

No picture shown on site. Does this knob have the M8 rod built into it like the original? Will it match this knob with rod from a Thule Sare Me rack? Thank you

asked by: Michael C

0

Expert Reply:

Yes, the Replacement Lockable Knob for Thule Spare Me Spare Tire Bike Rack # TH93NW has the M8 rod attached to it like what you show in the photo you submitted, and it will work with your Thule Spare Me bike rack no matter what generation you have so you're good to go!

I confirmed this with Thule directly.

expert reply by: Jon G

0

Locking Knob From Thule Spare Me Bike Rack
(click to enlarge)

Answer 1

The first thing you need to do is to make sure that the lock on your Thule T2 Pro XTR #TH83JV is unlocked first. The most common problem is trying to tighten the knob while it is locked. In order to solve this issue, you need to first unlock the…

view full answer...

Answer 2

Due to the age of your Thule Spare Me rack the correct replacement locking knob would be the part #TH93NW. To remove your old lock core from your knob to install in it the new knob would require the change key part #853-1251.

view full answer...

Answer 3

Yes the thread size of the knob part #TH79JV is M8 so it is perfectly compatible with the T-bolt part #853-0782 that you referenced.

view full answer...

Answer 4

We do carry all of the replacement parts for the SportRack Pathway Deluxe, part #SR2703 . I've listed them all below for you so you can pick and choose exactly what you need. Replacement Locking Knob without a bolt, part #05003400000 Replacement…

view full answer...

Answer 5

The correct replacement locking knob for a Thule Apex 4 Bike Rack 9025 is the Replacement Locking Knob part #TH79JV. In order to switch over the lock core from the old knob to the new knob you'll need the Change Key part #853-1251. In regards to…

view full answer...

Answer 6

I actually measured the bolt that would be used with handle #SR05003300000 and it is closest to 5/16. I have a gauge that I use to determine the size and the 3/8 slot was too big. Are you looking for a handle for a specific product or some other…

view full answer...

Answer 7

The replacement knob you would need for a SportRack Bike rack part #SR2703 would be the part #SR05003300000. For a replacement cradle you would want the part #05-0031-000. This is the top and bottom pieces. They are not available separately. For the…

view full answer...

Answer 8

In order to remove or install a Thule Lock Core, the Change Key is needed. The core cannot be inserted without it. We offer a replacement change key as part #853-1251. The core must be unlocked in order to use the change key to remove it. If you…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Lockable Knob for Thule Spare Me Spare Tire Bike Rack

Product Page this Question was Asked From

Continue Researching