Replacement Elbow Fittings for Lippert Level Up Jack System

Question

Question:

The jack on my 2015 Forest River Georgetown has a leak between the and the L shape hose end the the fitting that screws into the jack. The jack does not leak. I can-provide a picture if necessary. Question: can I get replacement fittings? Even if I were to replaced the jack it doesnt appear that a new jack comes with fittings.

asked by: John S

0

Expert Reply:

We have replacement elbow fittings for the Lippert Level Up systems with the part # LC113128 which would be correct part you'd need. You probably already thought to try this but you might make sure the fittings you have now are tight.

expert reply by: Jameson C

0

Motor and Hydraulic Lines
(click to enlarge)

Answer 1

Both the #LC359278 and #LC359275 are possible replacements for the system. Without parts to cross reference or measurements we can't identify which is correct until we get that information. Since you already measured this is easy to clear up. As…

view full answer...

Answer 2

The Lippert Replacement Atlas Jack for Kwikee Level Best Hydraulic Leveling System #LC359278 is an exact replacement for your current jack and so it does have the plugs at the top and bottom of the cylinder for the hydraulic lines (see attached). I…

view full answer...

Answer 3

The wires on the Lippert Replacement Atlas Jack for Kwikee Level Best Hydraulic Leveling System #LC359278 aren't polarity sensitive so you just connect one to power and one to ground. I reached out to my contact at Lippert and he said you just…

view full answer...

Answer 4

Yes the Lippert Replacement Atlas Jack for Kwikee Level Best Hydraulic Leveling System #LC359278 is a direct replacement for the jack leg you sent in a picture of.

view full answer...

Answer 5

I went ahead and reached out to Lippert, and they confirmed that you need automatic transmission fluid Dexron III or Mercon 5 fluid. This works with their hydraulic auto leveling system. With that being said, I do not recommend using the hydraulic…

view full answer...

Answer 6

Yes, the Replacement Hydraulic Jack Assembly #LC36VR does have 2 ports on top of the jack for connecting hydraulic lines.

view full answer...

Answer 7

Hello there. The Replacement Hydraulic Jack Assembly for Lippert Level Up System #LC36VR is 21 and 7/16 inches tall and has a travel length of 15 inches bringing its total height to 36 and 7/16 inches tall.

view full answer...

Answer 8

To install the Tekonsha Prodigy P3 Trailer Brake Controller #90195 in your 2019 Jayco Seneca on the Freightliner S2RV chassis the wiring is behind the kick panel in the drivers compartment. There is not a connector on the wires, they are simply…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Replacement Elbow Fittings for Lippert Level Up Jack System

Product Page this Question was Asked From

Continue Researching