Manual Switch Kit For Pace Edwards BedLocker Tonneau Cover BL2003

Question

Question:

I have a tonneau cover Model BL2003 . BI-1004-0023. The fob for this model is no longer available. Which manual kit should I ordwr?

asked by: Douglas D

1

Helpful Expert Reply:

You will need the Manual Switch Kit # 311-BL-1120 for your Pace Edwards BedLocker BL2003.

expert reply by: Bud M

1

Answer 1

I attached a picture of what the rail clamps part #311-TRPT1250-1 that you referenced look like installed.

view full answer...

Answer 2

There are some replacement parts available for the Pace Edwards BedLocker tonneau cover. There is a Replacement Tailgate Top Seal for Pace Edwards Retractable Tonneau Covers #PE99CV and there is also the Manual Switch Kit for Pace Edwards BedLocker…

view full answer...

Answer 3

For Pace Edwards hard covers, like the Pace Edwards Switchblade Retractable Hard Tonneau Cover #311-SWC95A17, we do carry replacement tailgate seal #PE99CV, passenger side rails #PE85GJ, and replacement driver side rails #311-RTPT1300-5117-L. These…

view full answer...

Answer 4

Typically if a Pace Edwards Retractable Tonneau Cover like the #311-M-BLFA18A44 is getting hung up it's with the railing and would require lubrication. The canister is a closed system so there isn't a good way to get into it and see if the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Manual Switch Kit For Pace Edwards BedLocker Tonneau Cover BL2003

Product Page this Question was Asked From

Continue Researching