Replacement Female Quick Disconnect Fitting For Demco SBS Air Force One Jumper Kit

Question

Question:

Hello, I purchase the Demco SBS Air Force One Coiled Air Jumper Kit for Freightliner BrakeSync-Equipped Chassis. It works great. My question is, can I also purchase only the female fitting that s into the coach side BrakeSync connector? Reason: I also have the original jumper hose that was provided by my RV dealer which does not fit on the chassis side. I want to make a backup jumper hose.

asked by: Kenneth D

1

Helpful Expert Reply:

The Replacement Female Quick Disconnect for Demco SBS Air Force One Supplemental Braking System # SM99613 is the correct replacement part for The Demco SBS Air Force One Coiled Air Jumper Kit # DM97ZR.

I attached a review video link below.

expert reply by: Noah E

1

Answer 1

For the SBS Air Force One you have installed on your 2017 Newmar Dutchstar the correct replacement jumper cable is the part #SM99666.

view full answer...

Answer 2

The correct replacement is going to depend on the supplemental braking system you currently have. If you have the SMI Air Force One Supplemental Braking System #SM99243 then the Replacement Air Jumper #SM99666 that you referenced would be the correct…

view full answer...

Answer 3

The Demco SBS Air Force One Coiled Air Jumper Kit for Freightliner BrakeSync-Equipped Chassis part #DM97ZR is for motorhomes that came with the Air Force One installed at the factory whereas the Replacement Air Jumper for Demco SBS Air Force One…

view full answer...

Answer 4

When it comes to replacing the male fitting on the end of the Demco Air Jumper Kit #DM97ZR you will need The Replacement Male Quick Disconnect for Demco SBS Air Force One Supplemental Braking System #SM99614. I attached a review video link below.

view full answer...

Answer 5

Whether or not you can flat tow with a Jeep bumper is really up to the manufacturers testing; some of the big names like MetalCloak or Poison Spyder have bumpers with D-ring attachments that can be used for flat towing connections. This is great…

view full answer...

Answer 6

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

We do offer tow bar setups that can attach to the D-rings on the Warn Elite Bumper. Your will need to use a D-ring adapter to connect the tow bar. For the adapter you have the following options: 1" Thick D-Rings #RM-035-1 3/4" Thick D-Rings…

view full answer...

Answer 10

I have a solution for you, however, I would not recommend mounting a tow bar directly to a bumper on a Jeep, whether it is OEM or an aftermarket bumper. Jeep does not recommend towing the Wrangler with the OEM bumper because it was not designed to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Robert; hopefully your Roadmaster tow bar is one that attaches to direct-connect base plates as opposed to crossbar base plates; for example the 8,000 lb Roadmaster Sterling would be optimal. Assuming that, here is what you need to flat tow your…

view full answer...