Trailer Hitch For A 2007 Toyota Matrix
Question:
How much does the C12013 itself weigh? Looking for a 2007 Toyota Matrix.
asked by: Michael S
Helpful Expert Reply:
We have the perfect trailer hitch that will fit your 2007 Toyota Matrix!
The Curt Trailer Hitch Receiver # C12013 has a shipping weight of 18 pounds. The hitch has a bolt-on installation with no welding required. It has a gloss black powder coat finish that is over a protective base coat that offers superior rust resistance.
The trailer hitch has a maximum gross trailer weight up to 2,500 pounds and has a maximum tongue weight up to 250 pounds. I would recommend checking your vehicle's manual to find out the proper towing capacity of your vehicle.
The T-One Vehicle Wiring Harness # 118386 will give you a 4-flat trailer connector that will make it to where your trailer's stop, turn, and taillights will mirror your vehicle's stop, turn, and taillights. The harness will plug into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo carrier.
You will also need The Draw-Tite Drawbar for 1-1/4 inch Hitch # 3593 and The 2 inch ball # 19258 or the 1-7/8 inch ball # 19256.
I attached a review video link below.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 250 lbs TW
- 2500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Q&A: Trailer Hitch and Wiring for a 2005 Toyota Matrix
- Article: Roadmaster Tow Bar Feature Descriptions
- Article: My Trailer Hitch Doesn't Fit
- Q&A: What do Trailer Acronyms GTW and TW Mean
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Replacement Motor and Gear Box for Landing Gear # ADTH 1RV-200 on Keystone Everest
- Q&A: Replacement Air Conditioner for RV Duo Therm 57915.531
- Article: Determining Trailer Tongue Weight
- Q&A: Hitch Installation on 2008 Toyota Matrix XR
- Q&A: Installation of Curt Class II Hitch C12013 on 2005 Toyota Matrix XR
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Hitch Receiver Sizes
- Article: Best Bike Racks for Electric Bikes